Regulations; Assistance; Product Description; Composition Of The Kit - SOMFY Dexxo Smart 800 io Manuel D'installation

Dexxo Smart 800 io / Dexxo Smart 1000 io
Do not use adhesive to mount the motorisation.
Install the internal manual back release device at a height of
less than 1.8 m.
Permanently affix the label concerning the manual back re-
lease device near its actuator.
WARNING
Take care when using the manual back release
device as an open door can suddenly drop if the
springs are weak, broken, or incorrectly balanced.
CAUTION
Install any fixed control device at a height of less
than 1.5 m and within sight of the door, but away
from moving parts.
After installation, ensure that:
• the mechanism is correctly set
• the manual back release device is operating correctly
• the motorisation changes direction when the door en-
counters an object 50 mm high on the ground.
Clothing precautions
Take off any jewellery (bracelet, chain, etc.) during installa-
tion.
For manoeuvring, drilling and welding operations, wear ap-
propriate protection (special glasses, gloves, ear protection,
etc.).
1.7

Regulations

Somfy declares that, when used in accordance with these
instructions, the product described in these instructions
complies with the essential requirements of the applicable
European directives, and in particular Machinery Directive
2006/42/EC and Radio Equipment Directive 2014/53/EU.
The full text of the EC declaration of conformity is available
at the following website: www.somfy.com/ce. Philippe
Geoffroy, Regulations Manager, Cluses.
1.8

Assistance

You may encounter difficulties or have questions when in-
stalling your motorisation.
Do not hesitate to contact us; our specialists are on hand to
answer all your questions.
Internet: www.somfy.com
2

PRODUCT DESCRIPTION

2.1

Composition of the kit

> > > Illustration 1
No. Quantity Designation
1 1 Motor head
2 1 Motor head cover
3 1 Integrated lighting cover
4 1 Lintel bracket
5 1 Door bracket
6 2 Ceiling mounting bracket
7 2 Motor head mounting bracket
8 1 Manual back release device
9 1 Connecting arm
10 1 End limit stop
11 4 Chain bearing
12 1 Power supply cord
©
Copyright 2021 SOMFY ACTIVITES SA. All rights reserved.
No. Quantity Designation
13 4 H M8x16 screw
14 4 H M8x12 screw and washer
15 6 HU8 nut
16 2 Shaft
17 2 Circlips
19 4 Self-tapping screw ∅ 4x8
20 2 Screw for plastic ∅ 3.5x12
21a 1 Single unit rail
21b 1 2-part rail
21b1 1 Sleeve
21b2 4 Self-tapping screw ∅ 4x8
22 2 HM8 self-locking nut
23 1 Bracket
24 2 Remote control *
* The model and number of remote controls may vary depending on the
pack.
2.2

Description of the printed circuit board

> > > Illustration 2
Off
Permanently lit
No. Designation Comments
1 SET indicator
light
programming is not carried out
etc.)
2 PROG indicator
light
confirmed
point
3 PROG button Memorise / delete radio control points
4 SET button Press for 0.5 s: enters and exits the parameter
setting menu
Press for 2 s: triggers auto-programming
Press for 7 s: clears auto-programming and
parameters
Interrupts auto-programming
5 - button Before auto-programming, close the door by
keeping the button depressed
Interrupts auto-programming
During parameter setting, modifies the value of
a parameter
6 + button Before auto-programming, open the door by
keeping the button depressed
Interrupts auto-programming
During parameter setting, modifies the value of
a parameter
Slow flashing
Rapid flashing
Very rapid flashing
: The first time the unit is powered on,
: Programming in progress
: Programming complete
: Electronic fault (motor thermal cut-out,
: Radio reception
: Memorisation of a radio control point
: Awaiting memorisation of a radio control
EN
17