Area Of Application; Motor Dimensions; Installation; Recommendations - SOMFY Dexxo Smart 800 io Manuel D'installation

EN
No. Designation Comments
7 Parameter P0: Operating mode
setting indicator
P1: Garage door speed
lights
P2: Slowdown zone
P3: Obstacle detection sensitivity
P4: Photoelectric cells
Px: Door type
8 Removable 230 V power supply
terminal block
9 Removable Auxiliary output
terminal block
10 Removable Photoelectric cells
terminal block
11 Removable Orange light
terminal block
12 9.6 V low- Compatible with 9.6 V batteries
voltage power
supply input
13 Removable Wired control point, photoelectric cells, gate
terminal block contact
14 Removable Remote antenna
terminal block
15 Photoelectric
: Normal operation
cells indicator
light
16 Not used
17 Gate contact
indicator light
18 Wired control
indicator light
19 Integrated
lighting
2.3

Area of application

> > > Illustration 3
This motorisation is exclusively designed to equip garage doors for residen-
tial use of the following types:
A: up-and-over doors
B: sectional doors
C: side doors
2.4

Motor dimensions

> > > Illustration 4
Overall length: L
Useful travel: C
Mounting: F
Rail: R
3

INSTALLATION

3.1

Recommendations

CAUTION
if the garage door is the sole means of access to the garage, install an ex-
ternal back release device (ref. 9012961 or ref. 9012962).
The position in which the motorisation will be fitted must allow for safe and
easy manual release of the product.
3.2

Installation height

> > > Illustration 5
Measure the distance "D" between the highest point of the door and the
ceiling.
• If "D" is between 35 and 200 mm, secure the assembly directly to the
ceiling.
• If "D" is greater than 200mm, secure the assembly so that the height
"H" is between 10 and 245 mm.
18
: Auto-test in progress
: Detection in progress / Permanent fault
: Gate contact open
: Control activated
3.3

Mounting the lintel yoke and door yoke

> > > Illustration 6
NOTICE
For maximum door heights, the motor travel can be optimised by mounting
the lintel yoke on the ceiling, with a gap of max. 200 mm from the lintel.
3.4

Assembling the rail in 2 sections

> > > Illustration 7
1] Unfold the 2 sections of the rail.
CAUTION
Ensure that the chain or belt is not twisted.
2] Assemble the 2 sections of the rail using the sleeve.
3] Secure the assembly using the 4 mounting screws.
NOTICE
In the case of an attached ceiling installation, do not use the sleeve mount-
ing screws.
CAUTION
The mounting screws must not penetrate the rail (do not drill).
4] Tighten the nut to tension the chain or belt. The compressed rubber
must measure between 18 and 20 mm.
3.5

Assembling the rail to the motor head

> > > Illustration 8
NOTICE
For maximum door heights, the motor travel can be optimised by fitting the
motor head at 90°.
3.6

Mounting on the lintel yoke

> > > Illustration 9
3.7

Mounting on the ceiling

Attached ceiling
> > > Illustration 10
Mounting directly on the ceiling using the rail.
NOTICE
Mounting points can be added on the motor head.
Detachable ceiling
> > > Illustration 11
Two options:
• mounting at the level of the motor head
• mounting at the level of the rail
For adjustable intermediate mounting along the rail, or mounting at a di-
mension h between 250 mm and 550 mm, use the ceiling mounting kit, part
no.: 9014462
3.8

Mounting the arm to the door and carriage

> > > Illustration 12
CAUTION
If the back release handle is higher than 1.80 m, it is necessary to extend the
cable to make it accessible to all users.
1] Release the carriage using the manual back release device.
2] Bring the carriage level with the door.
3] Secure the arm to the door yoke and carriage.
NOTICE
Cutting the arm
Sectional door: for optimum operation, the arm must form a 45° angle with
the rail. If necessary, cut the arm.
Up-and-over door: do not cut the arm.
Copyright
Dexxo Smart 800 io / Dexxo Smart 1000 io
a
b
©
2021 SOMFY ACTIVITES SA. All rights reserved.