Roland VS-2000 Mode D'emploi page 513

Program Change
Parameters on the Mixer/Effect section can be changed when UTILITY-MIDI screens
EFFECT P.C.Rx Sw is "On."
When UTILITY-MIDI screens EFFECT P.C. Rx Sw is "On," 00H-03H is received if it
operates as the Effect Program Change.
When UTILITY-MIDI screens SCENE P.C. Rx Sw is "On," MIDI Channel No. FH is received
if it operates as the Scene Change.
If V-LINK function is enable, see "5.V-LINK. "
If tracks 17/18 are assigned as RHYTHM TRACK, these messages are received on the MIDI
channel specified by the RHYTHM TRACK MIDI receive channel setting, and will change
drum kits.
Status Second
CnH ppH
n = MIDI Channel No.:
0H - 5H (ch.1 = FX1 ch.2 = FX2 ch.3 = FX3 ch.4 = FX4 ch.5 = FX5 ch.6 = FX6)
FH (ch.16 = Scene Memory (*1))
0H - FH (ch.1-ch.16) (*2)
pp = Program No. : 00H - 63H (0 - 99) n = 0H - 3H
pp = Program No. : 00H - 5FH (0 - 95) n = FH
pp = Program No. : 00H - 8H (0 - 8) (*2)
(*1) If received while VS-2000 is playing, play back stops,
and then restarts after the scene switched. Never receives while recording.
(*2) Only if tracks 17/18 are assigned as RHYTHM TRACK and the RHYTHM TRACK
MIDI transmit/receive channel is specified.
Pitch Bend Change
Receives when effect Algorithm 27 (Voice Transformer) is selected and MIDI control Sw is
On.
If the HARMONY ASSIGN screen's USE EFFECT BOARD setting is On, this message is
received on the MIDI channel specified by the HARMONY ALGORITHM VIEW screen's
MIDI setting.
Status Second
EnH llH
n = MIDI Channel No.: 0H - 5H (ch.1-ch.6)
n = 0,2,4 (ch.1 = FX1, ch.3 = FX3, ch.5 = FX5)
: Voice Transformer : Fine Pitch
n = 1,3,5 (ch.2 = FX1, ch.4 = FX3, ch.6 = FX5)
: Voice Transformer : Fine Formant
n = MIDI Channel No.: 0H - FH (ch.1-ch.16) (*1)
mm,ll = Value: 00H,00H - 40H,00H - 7FH,7FH
(-8192 - 0 - +8191)
(*1) Only if the HARMONY ASSIGN screen's USE EFFECT BOARD setting is On, and the
receive channel is specified by the HARMONY ALGORITHM VIEW screen's MIDI
setting.
Messages système communs
Messages MIDI Time Code Quarter Frame
MIDI Time Code Quarter Frame Messages can be transmitted while the VS-2000 is running
(Playing or Recording) if the UTILITY-SYNC screens SYNC MODE is "INT" and SYNC
Gen. is "MTC."
The transmitted time counts are summed to "SYNC OFF SET TIME" as the project top is
"00:00:00:00."
The VS-2000 synchronizes with the time counts which are summed to "SYNC OFFSET
TIME" as the project top is "00:00:00:00" if the SYNC screens SYNC MODE is "EXT."
Status Second
F1H mmH (= 0nnndddd)
nnn = Message type : 0 = Frame count LS nibble
1 = Frame count MS nibble
2 = Seconds count LS nibble
3 = Seconds count MS nibble
4 = Minutes count LS nibble
5 = Minutes count MS nibble
6 = Hours count LS nibble
7 = Hours count MS nibble
dddd = 4bit nibble data : 0H - FH (0 - 15)
If the upper and lower 4 bits of the count are combined, these bit fields are assigned as
follows.
Frame Count xxxyyyyy
xxx
yyyyy
Third
mmH
Reserved (000)
Frame No. (0-29)
Seconds Count xxyyyyyy
xx
yyyyyy
Minutes Count xxyyyyyy
xx
yyyyyy
Hour Count xyyzzzzz
x
yy
zzzzz
Song Position Pointer
The current position is transmitted with the Song Position Pointer Message before the
VS-2000 starts top run or after the locate operation when UTILITY-SYNC screens SYNC
MODE is "INT" and SYNC Gen. is "MIDIclk" or "SyncTr."
Status Second
F2H mmH
mm,nn = Song Position Point : 00H 00H - 7FH 7FH
Messages temps réel
Transmitted when UTILITY-SYNC screens SYNC MODE is "INT" and SYNC Gen. is
"MIDIclk" or "SyncTr."
Timing Clock
Status
F8H
Start
Status
FAH
Continue
Status
FBH
Stop
Status
FCH
System Exclusive
Status Data Byte
F0H iiH,ddH, ..., eeH
Byte Description
F0H Status of System Exclusive Message
iiH Manufacturer ID
41H Roland's Manufacturer ID
7EH Universal Non Real-time Message
7FH Universal Real-time Message
ddH Data: 00H - 7FH(0 - 127)
: :
eeH Data
F7H EOX (End of System Exclusive message)
The VS-2000 can transfer and receive the internal parameters information using system
exclusive messages, and also can be controlled by the external devices using system
exclusive message.
The VS-2000 can transmit and receive Universal System Exclusive messages, Data Request
(RQ1) and Data set (DT1) as the System Exclusive Message.
Model ID
The Model ID of the VS-2000 is 00H,61H as for Data Request (RQ1) and Data set (DT1).
The VS-2000 also can receive 00H,61H (VS-2000) and 00,36H (VE-7000).
Device ID
System Exclusive messages are not assigned to any particular MIDI channel. Instead, they
have their own special control parameter called device ID.
The roland system exclusive messages use device IDs to specify multiple VS-2000 units.
The VS-2000 sends system exclusive messages using 00H-1FH, and receives the system
exclusive messages whose device ID is same as its device ID and 7FH. the value of the
device ID is the value set on the UTILITY-MIDI screens DEVICE ID minus one.
Reserved (00)
Seconds Count (0-59)
Reserved (00)
Minutes Count (0-59)
Reserved (00)
Time Code Type
0 = 24 Frame/Sec
1 = 25 Frame/Sec
2 = 30 Frame/Sec (Drop Frame)
3 = 30 Frame/Sec (Non Drop Frame)
Hour Count
Third
nnH
Status
F7H
73