Stiga SRBA01 Manuel D'instructions page 13

3. OPERATION
3.1. MANUAL FUNCTIONING OF THE ROBOT
LAWN MOWER
The robot lawn mower can also be used without using the
work schedule programme. In this mode the robot lawn mower
carries out a work cycle, returns to the charging base and
remains there until the next manual start.
In order to use the machine in this mode, it is still however
necessary to programme the virtual perimeters, transition
routes and areas to be avoided. (See par. 2.4).
1. Place the robot lawn mower on the charging base or within
the perimeter of the installation.
2. Press the "STOP" button (Fig. 1.A) to open the cover
(Fig. 1.B) and access the control panel (Fig. 1.C).
3. Press the "ON/OFF" button (Fig. 1.E) for 5 seconds to
switch on the robot lawn mower.
4. Press the "SELECT MODE'"push button (Fig. 1.F) until
only the "SINGLE WORK CYCLE" is flashing (Fig. 1.L).
5. Press the "CONFIRM" push button (Fig. 1.G). The icon
(Fig. 1.L) is lit with a fixed light to confirm the operation.
6. Close the cover (Fig. 1.B). The robot lawn mower will
start operating.
NOTE: this mode may not guarantee adequate coverage
of the garden, both in terms of time required and in
terms of uniformity of the cutting result, especially if the
garden has an irregular shape. To achieve the maximum
efficiency of the robot lawn mower, it is recommended to
programme the work schedule.
3.2. DESCRIPTION OF THE CONTROLS ON THE
ROBOT LAWN MOWER
List of controls, indicators and their function:
• Press the "STOP" push button (Fig. 1.A): it is used to stop
the robot lawn mower safely.
• "SAFETY KEY" (Fig. 1.D): it is used to stop the robot lawn
mower safely.
• "ON/OFF" button (Fig. 1.E) is used to turn the robot lawn
mower on and off and to reset the alarms.
• "SELECT MODE" push button (Fig. 1.F): it is used to select
the operating mode of the robot lawn mower and to force
it to return to the charging base.
• "CONFIRM" push button (Fig. 1.G): it is used to confirm
the set operating mode.
• "SCHEDULED PROGRAMME" luminous icon (Fig. 1.l):
it is used to display the scheduled programme settings.
• "SINGLE WORK CYCLE" luminous icon (Fig. 1.L): it is used
to display the settings of the single work cycle.
• "RETURN TO BASE" luminous icon (Fig. 1.H): it is used to
display the settings of the forced return of the robot lawn
mower to the charging base.
• "BLUETOOTH" button (Fig. 1.M) is only used by the service
centre for diagnostic purposes.
• "ALARM" luminous icon (Fig. 1.N): it is used to display
alarm statuses.
• "BATTERY" luminous icon (Fig. 1.O): it is used to display
the battery charge level.
NOTE: For a more detailed description of the commands
listed above, please refer to the Full Manual.
EN
3.3. CHARGING BASE OPERATION
The charging base is equipped with a warning light (Fig. 8.N)
which lights up as shown below:
• Warning light off: the charging base is powered off or the
robot is on the base.
• Fixed warning light: the robot lawn mower is not connected
to the charging base and the antenna signal is correctly
transmitted.
• Flashing light: the charging base is not set up correctly,
or a charging base fault has been detected. Refer to the
Full Manual.
3.4. BATTERY CHARGING
The "BATTERY CHARGING" procedure allows to recharge
the robot lawn mower manually.
1. Position the robot lawn mower on the charging base
(Fig. 9.R).
2. Slide the robot lawn mower onto the charging base, until
the charging connector is engaged (Fig. 9.S).
3. Press the "STOP" button (Fig. 9.A) to open the cover
(Fig. 9.B) and access the control panel (Fig. 9.C).
4. Turn the robot lawn mower on with the "ON/OFF" button
(Fig. 9.E).
5. The "BATTERY" luminous icon (Fig. 9.O) flashes blue,
the robot lawn mower is charging.
6. Close the cover (Fig. 9.B).
7. Leave the robot lawn mower to charge for at least the
time shown in Par. 2.3.3.
NOTE: Charging the battery before winter storage should
be carried out as shown in Par. 4.3.
3.5. CUTTING HEIGHT ADJUSTMENT
Follow APP wizard to adjust the cutting height.
CAUTION:
Do not touch the cutting means when adjusting
the cutting height.
NOTE: The length of the grass cut by the robot lawn
mower must not exceed 10 mm.
4. MAINTENANCE
CAUTION:
Only use original spare parts.
CAUTION:
Do not modify, tamper with, elude or eliminate
the safety devices installed.
CAUTION:
Danger of cutting hands.
Use protective gloves to avoid cutting your
hands.
CAUTION:
Danger of dust in the eyes.
Use safety glasses to avoid the danger of
dust in the eyes.
5