Falcon Professional+ 110 Mode D'emploi page 25

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Feed the thermostat capillary out of the oven. Disconnect
the wiring from the thermostat. Remove two screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped to
the oven back with the phial centrally positioned between the
clips.
Check the operation of the thermostat.
7. To Replace the Grill Controller
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2). Disconnect
wiring from controller. Remove two screws holding controller
to mounting panel. Fit new controller and reassemble in
reverse order. Check for correct operation.
BEFORE SERVICING ANY GAS CARRYING

COMPONENTS, TURN OFF THE GAS SUPPLY.
8. To Replace the Hotplate Control Taps
Disconnect from the electricity supply.
Remove the control panel and hotplate (see 1 & 2). Unplug
the FSD lead from the rear of the tap. Undo the compression
fitting at the rear of the tap. Remove the fixings that secure the
tap to the gas rail. Disconnect the ignition switch wiring.
Remove the tap. Remove and discard the gasket seal. Fit
the new gasket seal to the replacement tap. Reassemble in
reverse order. Check that the appliance is gas sound. Verify the
hotplate ignition.
9. To Change Hotplate Burner Injector
Remove burner cap and head. Remove old jet. Fit new injector.
Reassemble in reverse order. Check appliance is gas sound.
10. To Replace a Hotplate Burner Electrode
Lift off pan supports, remove burner cap. Remove the screw
holding the electrode. Pull electrode vertically up sufficiently
to grip the lead between thumb and forefinger. Pull off the
electrode, but keep hold of the lead. Fit new electrode to the
lead. Fix electrode in burner with screw. Replace burner cap.
Check the burner ignition. Replace pan supports.
11. To Replace a Hotplate Burner
Remove the hotplate tray (see 2). The burners except the
right-hand wok burner are mounted on support struts. For
these burners, disconnect the burner feed pipes at the burner.
Remove the screws at the front and rear holding the support
stru ts. Lift the strut and burners clear. The burners are fixed to
the support struts with two screws. Remove the appropriate
burner and fit the new one. Reassemble in reverse order.
Check that the burner operation is satisfactory.
Right-hand Wok burner
Disconnect the burner feed pipes at the burner. Fit the new
one and reassemble in reverse order. Check that the burner
operation is satisfactory.
All manuals and user guides at all-guides.com
23
12. To Replace an Oven Door
Open the oven door. Support the door and remove the two
screws securing the upper hinge and gasket to the cooker
front. Remove the door from the lower hinge by lifting slightly
and moving outwards.

The door is heavy, so take care.
Reassemble in reverse order.
13. To Replace an Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel fixing
screws from the door sides (two each side).
ArtNo.320-0002 Oven door side screws
Carefully lift off the outer door panel.
Remove the door handle from the panel by unscrewing the
two retaining nuts. Fit the door handle to the new panel.
Fit the panel to the door. Reassemble in reverse order.
14. To Change the Oven Door Latch
Remove the outer door panel (see 13). Remove screws 'B' that
hold the latch assembly to the inner door panel. Fit the new
catch and reassemble in reverse order.
Verify the door operation.
�
ArtNo.320-0003 Oven door latch
15. To Adjust an Oven Door Catch Keep
Open oven door, slacken off the locknut at the base of the
keep, and screw in or out as required until the required fit is
obtained. Retighten the locking nut.
ArtNo.320-0004 Oven door keep