Redmond SkyCooker RMC-M92S-E Mode D'emploi page 10

Non-volatile memory
REDMOND SkyCooker RMC-M92S-E has a non-volatile memory. In the event of a power outage while the cooking program is
running, the settings are stored in the appliance's memory. When the power is restored, the display will remain on until the
power is turned off.
If the temperature difference in the bowl is less than 5°C when the power is switched off and on, the appliance will continue
to operate.
If the temperature difference is greater than 5°C, the program will be paused – the time indicator and the running program
indicator will flash on the display. There is no countdown of cooking time. At the same time, once a minute for half an hour 1
beep will sound.
To continue the cooking process, press and hold down the Start button. The cooking time indicator will be on continuously.
The countdown will continue.
If the cooking process does not continue for 30 minutes, the appliance will go into the standby mode. Press and hold down
the Reheat/Cancel button to stop the cooking indicator from blinking.
If the power supply is turned off during the time delay operation, the display will remain on when the power is turned on
until the time delay function indicator flashes, the cooking program will continue to work.
To interrupt the time delay, press and hold down the Reheat/Cancel button.
Setting The Cooking Time
The multicooker allows manually adjusting the cooking time, set by default for each program (except EXPRESS). Time adjust-
ment range and interval depend on the program of cooking selected.
The time indicator will start flashing when the cooking program is selected. To increase the hour value press the Hour button, to
increase the minute value – the Min button. Press and hold the corresponding button down to scroll through the digits.
In certain automatic programs countdown starts only when the device reaches its operating temperature. E.g. If you set STEAM
program on 5 minutes, the countdown of the program begins only when the water comes to a full boil providing enough steam.
In PASTA program, the countdown begins after water starts boiling and Start button is being repressed.
Time Delay Function
This function allows setting the program to finish by certain time. Cooking time may be delayed for a period from 10 minutes
to 24 hours with 10 minute intervals. Setting Time Delay function, take the cooking time of the program into consideration.
The time of a delay should be longer than the cooking time of the program selected; otherwise the program starts running
right after you press Start.
To set the time of delay press the Time delay button after the program selection. To increase the hour value press the Hour button,
to increase the minute value – the Min button. Press and hold the corresponding button down to scroll through the digits.
Time Delay function is available in all automatic programs except FRY, PASTA and EXPRESS.
It is not recommended to use Time Delay function if dairy and other perishable products are being used (eggs, fresh milk, meat,
cheese etc.).
Keep Warm Function
Function is being automatically activated at the end of the cooking program. When the program finishes, the temperature of
the meal (70–75°C) is being maintained for a period of time up to 12 hours. The Reheat/Cancel indicator is lit with the ena-
bled Keep Warm, the direct counting of the program time in this mode is displayed.
Keep Warm may be disabled if necessary by pressing and holding the Reheat/Cancel button until an audible signal is heard.
The function is not applicable in PASTA, YOGURT/DOUGH and EXPRESS programs.
When setting the cooking temperature below 80°C in the MULTI COOK program the Keep Warm function will be disabled by
default. To enable Keep Warm press and hold down the Menu / Keep Warm button during program operation.
Disabling The Keep Warm In Advance
Automatic activation of the Keep Warm function at the end of the program may sometimes be undesirable. The multicooker
allows disabling the function in advance, while setting the program or during its operation. Press and hold down the Menu /
Keep Warm button to cancel the function. Reheat/Cancel button indicator goes off. To reactivate the function, repress and
hold down the Menu / Keep Warm button (Reheat/Cancel button indicator goes off).
10
Reheat Function
The multicooker can be used for warming up cold meals. To reheat:
1. Put the products into the bowl. Place the bowl inside the device.
2. Close the lid until it clicks into place and plug in the unit.
3. Press and hold down Reheat/Cancel button for a few seconds until an audible sound is produced. Corresponding indica-
tors light up and reheating process begins. The timer starts its countdown.
The meal will be warmed up to 70–75°C and the temperature will be maintained for the next 12 hours. To cancel the function
press and hold down Reheat/Cancel button. Corresponding indicators go off.
The function may operate for a period of 12 hours, however, we recommend using it moderately, because a prolonged thermal
exposure may sometimes affect flavor characteristics of the meal.
Standard Operating Procedure for Automatic Programs
IMPORTANT! When using the water boiling device (for example, when boiling products), DO NOT set the cooking temperature
above 100°C. It may result in overheating and failure of the device. For the same reason, DO NOT use the BAKE, FRY and BREAD
programs to boil water.
1. Measure the ingredients according to the recipe.
2. Put them into the bowl. Make sure that all the ingredients including liquid are below the scale mark indicating maximum
capacity. Place the bowl inside the device. The bowl and the heating element must fit tightly.
3. Close the lid until it clicks into place. Plug in the unit.
ATTENTION! If you cook at high temperatures using a large amount of vegetable oil, always leave the lid of the device open.
4. Repeatedly press Menu / Keep Warm button to select the program (corresponding indicator lights up).
To start the EXPRESS program from the standby mode press and hold down the EXPRESS button, until the EXPRESS indicator
lights up on display. During this program operation the program countdown is not displayed.
5. The MULTI COOK program provides the cooking temperature adjustment before the start of the program (default
temperature is 100°С). Set the desired value by pressing the Temperature button.
6. You can adjust cooking time value.
7. Set time of delay if necessary.
8. Press and hold for several seconds the Start button to begin cooking cycle. Start and Reheat/Cancel indicators will light
up solid. Depending on the selected cooking program the countdown will start immediately or after water in the bowl
comes to the boil.
When using the PASTA program an audible signal will inform you of water boiling and the necessity of adding the ingredients.
The time starts to countdown after repressing Start.
9. To preliminarily disable the Keep Warm function, press and hold down the Menu / Keep Warm button (the (Reheat/
Cancel button indicator will go out). You may re-enable this function by repressing the Menu / Keep Warm button.
10. An audible signal will be produced to indicate that cooking cycle is complete. Depending on selected programme or
current settings the appliance will either enter Keep Warm (Reheat/Cancel is lit on the display) or Standby mode Start
button indicator is flashing).
To interrupt cooking process at any stage, to cancel set program or the Keep Warm function press and hold down Reheat/
Cancel button.
For high-quality results, you are offered to use the recipes for cooking from the cook book supplied with REDMOND multi-
cooker SkyCooker RMC-M92S-E, designed specifically for this model.
If you did not achieve the desired result using automatic programs, try versatile program called MULTI COOK, featuring a wide
time and temperature adjustment range. This program gives endless opportunities for new culinary experiments.
Table of Default Settings
Program Recommendations for use
Cooking various meals with your personal time and
MULTI COOK temperature settings. Temperature adjustment range
is from 35 to 170°C with 1°C intervals
Default
cooking Time
5 min – 1 h / 1 min
30 min 24 12
1 h – 12 h / 5 min