Rating Plate Information - Napoleon HYBRID 150 Instructions D'installation Et D'opération

8
2.4

RATING PLATE INFORMATION

W415-0910 / A / 09.16.10
Rating plate is located above and below the domestic hot water inlet and outlet.
CAN-CSA B366-1-M91 / UL391 4th Ed 2006 (JULY 2008) / UL 727 / CSA B140.4 / CSA B212
INSTALLATION USE ONLY IN ACCORDANCE WITH WOLF STEEL LTD'S INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS OR OTHER AUTHORITIES HAVING
JURISDICTION ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
CAUTION: THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER. USE OF UNAUTHORIZED COMPONENTS OR FAILURE TO COMPLY WITH INSTALLA-
TION INSTRUCTIONS WILL RESULT IN VOIDED WARRANTY.
CHIMNEY TYPE: FOR "WOOD ONLY" FURNACE CONFIGURATION MINIMUM 6" (152mm) DIAMETER LISTED (UL 103HT) RESIDENTIAL CHIMNEY. FOR "WOOD/OIL
COMBINATION" FURNACE RECOMMENDED MINIMUM 7"(178mm) DIAMETER LISTED (UL 103HT) RESIDENTIAL CHIMNEY.
CHIMNEY CONNECTOR: 6" (152mm) DIAMETER MINIMUM 24 GAUGE STEEL MINIMUM CLEARANCE FROM HORIZONTAL CONNECTOR AND CEILING 18" (455mm).
SPECIAL METHODS ARE REQUIRED WHEN PASSING A CHIMNEY THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING CODES.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. EXCEPTION "ADD ON" CONFIGURATION WITH AN OIL FURNACE REFER TO MANUAL.
DO NOT CONNECT THIS FURNACE TO A CHIMNEY SERVICE A GAS APPLIANCE.
FUEL: FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. LOAD FUEL CAREFULLY OR DAMAGE MAY
RESULT. OIL FURNACE MODULE NO.2 FURNACE OIL
DANGER: RISK OF FIRE OR EXPLOSION.
DO NOT ATTEMPT TO LIGHT A FIRE IF THERE IS AN OIL VAPOUR PRESENT.
DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE.
DO NOT BURN GARBAGE, GASOLINE, NAPHTA, ENGINE OIL OR OTHER INAPPROPRIATE MATERIALS.
DO NOT STORE FUEL OR COMBUSTIBLE MATERIAL WITHIN INSTALLATION CLEARANCES OF THE APPLIANCE.
DO NOT USE THIS FURNACE WITHOUT DUCTS – SEE MANUAL FOR ALLOWABLE CONFIGURATION.
WARNING:
RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH FIRING AND ASHPIT DOOR TIGHTLY CLOSED. DO NOT OVERFIRE.
IF HEATER OR CHIMNEY CONNECTORS GLOW, YOU ARE OVERFIRING – IMMEDIATELY TURN OFF THERMOSTAT AND
ENSURE PRIMARY SHUTTER FIRING AND ASHPIT DOOR ARE CLOSED.
CAUTION: MAINTAIN COMBUSTION AIR SUPPLY TO BOTH FURNACES. AIR STARVATION IS DANGEROUS (SEE MANUAL UNDER "OUTSIDE COMBUSTION AIR".
THE HMF150 FURNACE MAY BE CONNECTED TO DUCTWORK (SUPPLY SIDE – SEE MANUAL) OF ANOTHER FURNACE WHEN USED AS AN WOOD FURNACE "ADD-ON".
CERTIFIED FOR SERIES CONNECTION TO THE SUPPLY PLENUM OUTLET ONLY OF A GAS FIRED, OIL FIRED, OR ELECTRIC FURNACE.
DO NOT CONNECT DUCTWORK SO THAT REVERSE FLOW IS POSSIBLE.
FOR "ADD ON" INSTALLATION REFER TO MANUFACTURES INSTRUCTIONS FROM ORIGINAL FURNACE FOR INFORMAITON ON MINIMUM DUCT SIZING, ALLOWABLE
DUCT OPENINGS IN FURNACE CASING AND ELECTRIC DIAGRAMS AND INFORMATION.
DO NOT RELOCATE OR BYPASS ANY OF THE SAFETY CONTROLS IN THE ORIGINAL FURNACE INSTALLATION ("ADD ON" CONFIGURATION).
DO NOT OBSTRUCT SPACE UNDER FURNACE. UNIT CAN BE INSTALLED ON COMBUSTIBLE SURFACE (WOOD SUBSTRATE ONLY – CARPET AND OTHER FLOOR
COVERINGS TO BE REMOVED) PROVIDING EMBER STOP SHIELD (SEE MANUAL) INSTALLED BETWEEN FURNACE AND FLOOR AND MINIMUM 1 ¼" AIR GAP
MAINTAINED BETWEEN FURNACE AND FLOOR.
INCASE OF POWER FAILURE: PUSH DOWN ON THE CONTROL ARM OF THE PRIMARY AIR CONTROL AND LOCK IT DOWN USING ROTATING CLASP. TO AVOID
EXCESSIVE HEAT BEING TRAPPED IN DUCT WORK ENSURE ALL RETURN AND SUPPLY AIR REGISTERS ARE NOT BLOCKED BY OBJECTS OR DEBRIS AND ALL DUCT
CONTROL DAMPERS ARE SET OPEN. SEE MANUAL FOR OPERATION OF WOOD FURNACE IF ELECTRICAL POWER HAS BEEN INTERRUPTED.
OPERATE ORIGINAL FURNACE (ELECTRIC, OIL, GAS) OF A "ADD ON" CONFIGURATION PERIODICALLY TO ENSURE IT WILL OPERATE SATISFACTORILY WHEN NEEDED.
THE HEAT EXCHANGER, FLUE PIPE AND CHIMNEY MUST BE INSPECTED FREQUENTLY AND CLEANED REGULARLY TO REMOVE ACCUMULATED CREOSOTE AND
ASH. UNDER CERTAIN CONDITIONS OF USE, CREOSOTE BUILDUP MAY OCCUR RAPIDLY. ENSURE THAT THE HEAT EXCHANGER, FLUE PIPE AND CHIMNEY ARE
CLEANED AT END OF BURNING SEASON, THIS HELPS TO MINIMIZE CORROSION IN THE SUMMER MONTHS. THE APPLIANCE, FLUE PIPE AND CHIMNEY MUST BE
MAINTAINED IN GOOD CONDITION. UNSAFE TO FIRE WITH WOOD ABOVE TOP OF REFRACTORY BRICK INSIDE COMBUSTIBLE CHAMBER.
USE SUPPLY WIRES SUITABLE FOR 90°C. SEE INSTRUCTION MANUAL FOR ELECTRICAL DIAGRAM.
DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. FOR MORE INFORMATION REFER TO OWNER'S MANUAL.
CAUTION: TWO SOURCES OF ELECTRICAL ENERGY PRESENT IN ELECTRIC FURNACE MODULE - DISCONNECT 220V SUPPLY TO MODULE AND 120V SUPPLY TO
HMF150 FURNACE BEFORE SERVICING.
REPLACE ALL CRACKED OR BROKEN FIRE BRICK AND TOP BAFFLES. REPLACE GLASS ONLY WITH CERAMIC GLASS.
AUTHORIZED MODULES FOR CONNECTION TO HMF150 FURNACE: BLOWER BOX MODULE - HMFK-BMP33, ELECTRIC FURNACE MODULE-HMFK-EF20, OIL FURNACE
MODULES - HMFK-OFRF40, HMFK-OFAFG, DHW PREHEAT MODULE - HMFK-DHW, "ADD ON" KIT - HMFK-ADDON
THESE ARE THE ONLY AUTHORIZED COMPONENTS THAT MAY BE ATTACHED TO THE HMF150 FURNACE ASIDE FROM CONNECTION TO FORCED AIR SYSTEM
RETURN AND SUPPLY PLENUMS. MODULES MUST BE INSTALLED TO MANUFACTURERS INSTRUCTIONS POSTED IN THE INSTALLATION/OWNERS MANUAL ACCOMPA-
NYING HMF150 AND INSTRUCTION ADDENDUMS INCLUDED WITH EACH MODULE.
HMF150 CONFIGURED AS AN "ADD ON":
MAY BE ADDED ONTO A FURNACE HAVING A RATING AS SHOWN ON THE ORIGINAL NAME PLATE BETWEEN:
REFER TO OWNERS MANUAL
LEFT HAND RA CONFIGURATION (REAR VIEW)
WOOD, WOOD/OIL FLUE
18"
18"
MAX 16"
9"
14"
14"
24"
24"
*Drawing not to scale
NOTE
CHANGE WITH ADDITION OF THE ELECTRIC FURNACE.
CAUTION:
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND
FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND
INSTRUCTIONS.
WOLF STEEL LTD.
24 NAPOLEON ROAD, BARRIE, ON, L4M 4Y8 CANADA
LISTED SOLID FUEL FIRED CENTRAL FURNACE
TESTED TO:
MODEL: HMF150
LEFT HAND RA CONFIGURATION (SIDE VIEW BLOWER MODULE)
18"
WOOD, WOOD/OIL FLUE
9"
48"
24"
1.25"
*Drawing not to scale
CLEARANCE TO COMBUSTIBLES
415-S-09-2
REPORT NO.: _
TECHNICAL DATA
BLOWER MOTOR 1/3 HP
ELECTRICAL RATING 120V, 11 AMPS, 60Hz
ELECTRIC FURNACE MODULE 220V, 84 AMPS
EXTERNAL STATIC PRESSURE 0.2" W.C., 0.2" C.E.
DRAFT PRESSURE
WOOD FLUE: MIN. 0.04" W.C. TO MAX. 0.06" W.C.
OIL FLUE: MIN. 0.02" W.C. TO MAX. 0.04" W.C.
OIL FURNACE MAX. FIRING RATE 91,000 BTU INPUT
AS SHIPPED: - OIL PRESSURE: 120 PSI
- NOZZLE: 0.65 - 60°A
- NO. 2 FURNACE OIL
SECTION
CLEARANCE TO COMBUSTIBLES
A B
TOP 6" 6"
BOTTOM/SIDES 18" 6"
CLEARANCE TO COMBUSTIBLES
6"
A
40"
NOTE:
72"
B
See
CAN/CSA-
B365.01 and
NFPA211 for
clearance to
combustible
specifications
for return air
ducting.
*Drawing not to scale.
NOTE:
SECTION "C" CLEARANCES MAY BE REDUCED TO 0.375" BEYOND A BEND OR
OFFSET IN THE DUCT SUFFICIENTLY LARGE TO SHIELD THE REMAINDER OF
THE SUPPLY DUCT FROM DIRECT RADIATION FROM THE FURNACE HEAT
EXCHANGER.
MANUFACTURE DATE:
2010 2011 2012
JAN APR JUL
FEB MAY AUG
MAR JUN SEP
SERIAL
HMF150
NO.
W385-0413 / 07.16.10
C
1"
1"
1"
C
>72"
2013
OCT
NOV
DEC