HearthStone WFP-75 8411 Manuel D'installation Et D'utilisation page 108

Report prepared for Guillaume Thibodeau-Fortin (Stove Builder International Inc.) on
6/8/2020 7:48:41 AM
103704002MTL-001 TEST REPORT REV 4
TEST REPORT FOR STOVE BUILDER INTERNATIONAL INC.
Report No.: 103704002MTL-001
Date: 11/16/18
K
P
L
a
L
p
m
p
m
f
m
g
m
r
m
n
M
s
P
bar
P
g
P
R
P
s
P
std
Q
std
T
m
T
mi
where:
T
mi(b)
T
mi(e)
Ts
Tsi
where:
T
si(b)
T
si(e)
Version: 05/10/17
Stove Builder International Inc. | 46345 | Rev: Apr 13 2020 12:33PM | Uncontrolled Copy
��
= Pitot Tube Constant, 34.97
sec⁡
or
����
= Pitot Tube Constant, 85.49
sec⁡
= Maximum acceptable leakage rate for either a pretest or post-test leak- check, equal
to 0.0003 m3/min (0.010 cfm) or 4 % of the average sampling rate, whichever is less.
= Leakage rate observed during the post-test leak-check, m3/min (cfm).
= mass of particulate from probe, mg.
= mass of particulate from filters, mg.
= mass of particulate from filter gaskets, mg.
= mass of particulate from the filter, filter gasket, and probe assembly from the room air
blank filter holder assembly, mg.
= Total amount of particulate matter collected, mg.
= the dilution tunnel dry gas molecular weight (may be assumed to be 29 g/g mole (lb/lb
mole).
= Barometric pressure at the sampling site, mm Hg (in. Hg).
= Static Pressure in the tunnel (in. water).
= Percent of proportional sampling rate.
= Absolute average gas static pressure in dilution tunnel, mm Hg (in. Hg).
= Standard absolute pressure, 760 mm Hg (29.92 in. Hg).
= Average gas flow rate in dilution tunnel.
Q = 60 (1 - B ) V A [T P /T
std ws s std s s
dscm/min (dscf/min).
= Absolute average dry gas meter temperature, K (R).
= Absolute average dry gas meter temperature during each 10-min interval, i, of the test
run.
T = (T + T )/2
mi mi(b) mi(e)
= Absolute dry gas meter temperature at the beginning of each 10-min test interval, i, of
the test run, K (R), and
= Absolute dry gas meter temperature at the end of each 10-min test interval, i, of the
test run, K (R).
= Absolute average gas temperature in the dilution tunnel, K (R).
= Absolute average gas temperature in the dilution tunnel during each 10-min interval, i,
of the test run, K (R).
T = (T + T )/2
si si(b) m=si(e)
= Absolute gas temperature in the dilution tunnel at the beginning of each 10-min test
interval, i, of the test run, K (R), and
= Absolute gas temperature in the dilution tunnel at the end of each 10-min test
interval, i, of the test run, K (R).
��
( ∎��������)(����⁡����)
1
��
[ ]
2
(��)(����⁡����������)
����
( −��������)(����⁡����) 1
[ ���� ]
2
(��)(����⁡����������)
P ]
std
Page 11 of 21
(11 OF 21)
1829, 32nd Avenue
Lachine, Que,H8T 3J1
Telephone: 514-631-3100
Facsimile: 514-631-1133
www.intertek.com/building
GFT-OP-10c
Page 787 of 971