WAGNER PlastCoat PC15 Mode D'emploi page 35

Plast Coat 15
EDITION 09 /2004
Contents
1 SAFETY REQUIREMENTS______________________ 36
2 INTRODUCTION TO WORKING WITH THE MORTAR
SPRAYING MACHINE PLASTCOAT 15____________ 37
2.1 Operation of the mortar _______________________ 37
2.2 What materials can be sprayed? _________________ 37
3 TECHNICAL DATA ___________________________ 37
4 EQUIPMENT OVERVIEW - MORTAR SPRAYING
MACHINE PLASTCOAT 15 _____________________ 38
4.1 Control unit _________________________________ 39
4.1.1 Symbols on the changeover switch ______________ 39
4.2 Drive_______________________________________ 39
4.3 Receptacle __________________________________ 39
4.3.1 Sliding cover ________________________________ 40
4.3.2 Sack mangle ________________________________ 40
4.3.3 Container suction system ______________________ 40
4.4 Compressor (accessory) _______________________ 40
4.5 Mortar hose with electrical remote control ________ 40
4.6 Spray lance with automatic control ______________ 41
4.7 Spray lance without automatic control ___________ 41
5 TRANSPORT ________________________________ 41
5.1 Transport using a crane________________________ 41
6 COATING MATERIALS EQUIPMENT TABLE _______ 42
7 PLACING INTO OPERATION ___________________ 44
7.1 Installation location___________________________ 44
7.2 Compressor (accessory) _______________________ 44
7.3 Connecting mortar hose_______________________ 44
7.4 Connecting spray lance with automatic system ____ 44
7.5 Connecting spray lance without automatic system _ 44
7.6 Extension cable ______________________________ 45
7.7 Preparing the mortar spraying machine __________ 45
7.8 Spray lance with automatic control ______________ 45
7.9 Spray lance without automatic control ___________ 45
7.10 Spray lance with automatic control ______________ 45
7.11 Spray lance without automatic control ___________ 45
7.12 Spray lance with automatic control ______________ 46
7.13 Spray lance without automatic control ___________ 46
7.14 Starting the spraying procedure ________________ 46
7.15 End of the spraying procedure __________________ 46
8 GENERAL REQUIREMENTS FOR APPLICATION
TECHNOLOGY ______________________________ 46
8.1 Spraying technique ___________________________ 46
9 FITTING ACCESSORIES _______________________ 47
9.1 Compressor _________________________________ 47
9.2 Sack mangle ________________________________ 47
9.3 Container suction system ______________________ 48
10 PLACING OUT OF OPERATION AND CLEANING ___ 48
10.1 Cleaning the mortar hose ______________________ 49
10.2 Cleaning device and changing pump jacket _______ 49
11 MALFUNCTION CHECKLIST ___________________ 50
10.3 Cleaning spray lance __________________________ 50
12 SERVICING _________________________________ 52
12.1 Electrical equipment __________________________ 52
12.2 Long-term storage ___________________________ 52
13 SPARE PARTS LIST PLASTCOAT 15______________ 53
14 SPARE PARTS LIST - SPRAY LANCE WITH
AUTOMATIC CONTROL _______________________ 55
15 SPARE PARTS LIST - SPRAY LANCE WITHOUT AUTO-
MATIC CONTROL ____________________________ 57
16 SPARE PARTS LIST -COMPRESSOR V 400 ________ 58
17 SPARE PARTS LIST -COMPRESSOR C 350 ________ 58
18 SPARE PARTS LIST - CONTAINER SUCTION
SYSTEM ____________________________________ 59
19 ACCESSORIES PLASTCOAT 15 _________________ 60
Manufacturing and sales companies _________________ 63
Important notes on product liability __________________ 64
Note on disposal__________________________________ 64
Guarantee declaration _____________________________ 64
Declaration of conformity_______________________ 64
Sales and Service companies_______________________ 124
GB
CONTENTS
35