Publicité
PRODUCT FEATURES
Built-in or Free-standing installation with single,
dual or three temperature zone, depending on your
model.
Continuously
variable
control
with digital
touchpad input.
Temperature can be set from 5° to 20°C (41° to
68°F) for either compartment and can be displayed
in either Fahrenheit or Celsius degree.
Can be set to the long time storage maturing
temperature or a specific serving temperature for
red/white/sparkling wines.
Cooling and Heating to maintain the perfect
storage and/or service condition.
Dynamic compressor type cooling to ensure
interior air circulation with even distribution of
temperature and humidity.
Soft LED Interior Light with ON/OFF switch –
Function mode and Showcase mode.
Adjustable display brightness and interior lighting
brightness.
Open-door and malfunction warning system.
Sabbath mode will allow the lights to remain off
during certain religious observances.
Temperature memory function - If power is
interrupted (power surge, breaker switch, etc.) and
then powered up again, the unit will operate with
the last temperature set-point.
Automatic defrosting with defrost water evaporation.
Reversible tempered double/triple pane gray glass
door protects your wine from UV light and creates
an attractive display with minimal condensation
and low noise.
Black coated matte steel outer frame and black
plastic interior liner offer lifetime performance and
stability. The black liner prevents excessive light
from damaging the maturing process.
Adjustable solid Sapele shelves allow for maximum
convenience
and
various size bottles.
Environmentally friendly refrigerant and foaming
insulation gas.
Humidity control system (Humidity Box).
Active charcoal air filter.
NOTE: Features and specifications are subject to
change without notice.
Code Rev. E 20240815 (IEC)
electronic
temperature
display
and
S
MART
flexibility
to
accommodate
INSTALLATION
BEFORE USING YOUR APPLIANCE
Remove all exterior and interior packing. Clean the
interior surface with lukewarm water using a soft
cloth. The unit may have residual odors at first,
L
IGHT
they will disappear as the unit cools.
Before connecting the appliance to the power
source, let it stand upright for at least 24 hours.
This will reduce the possibility of a malfunction in
the cooling system caused by handling during
transportation to ensure that oil flows back into the
compressor. During this time we recommend that
you leave the door open to clear any residual odors.
The door on this appliance can be opened from
either the left or the right side. The unit is delivered
with the door opening on the left side. Should you
wish to open the door from the right, follow the
instructions 'Reversing the door hinge'.
Install the handle on the door if necessary.
INSTALLATION OF YOUR APPLIANCE
The appliances are designed to be built-in or
recessed or freestanding installation depending on
your model. For the freestanding installation only
models, it is not intended to be used as a built-in
appliance.
WARNING: Do not store or install the appliance
outdoors. The unit is for indoor use only.
WARNING: Do no install the appliance in the
laundry. Avoid locating the unit in damp areas.
Place your appliance on a floor/surface that is
strong enough to support it when it is fully loaded.
To level your unit, adjust the front leveling leg at
the bottom of the unit.
For freestanding installation, 100mm of space
between the back and sides of the unit are
suggested, which allows the proper air circulation
to cool the compressor and condenser for energy
saving. Even with built-in installation, it is a must to
keep 5mm space on each side and at the top to
ensure proper service access and ventilation. Take
care that the air vent at the front of the appliance
must never be covered or blocked in any way.
Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and
heat sources may increase electrical consumption.
Extreme cold ambient temperatures may also
cause the unit not to perform properly.
Plug the unit into an exclusive, easily accessible
plug socket. Any questions concerning power
and/or grounding should be directed towards a
qualified electrician or an authorized products
6
Publicité
