Publicité
1
6
3
4
1
2
5
1.
Remove the glass door by unscrewing the eight
lock screws (5) and (6). Be careful to hold the
glass door firmly after removing the screws and
place it on a padded surface to avoid the risk of
damage.
2.
Unscrew the screws (1) and (3) then transfer the
door supporter (2) and decoration cover (4) to the
opposite side.
3.
Rotate the glass door 180° and refit the glass door
to the opposite side. Then screw and tighten it
after the door is leveled.
DESIGN 3 – For high models
4
1
2
3
1
11
4
1. Remove the right bottom hinge (2) and/or left
bottom hinge (1) by unscrewing the eight lock
screws (3). Be careful to hold the door (4) firmly
after removing the screws. (Fig. 1)
2. Gently pull down to remove the door from the right
top hinge and place it on a padded surface to avoid
the risk of damage. Then remove the right top
hinge (12). (Fig. 4)
3. Pop out the cover caps on the left side of cabinet
and use them to
cover the screw holes on the right
hand side.
4. Screw the alternative left top hinge (11), included in
the fittings,
on the left hand side of cabinet. (Fig. 4)
5. Unscrew and transfer hinge pin (6) and/or door
supporter (5) to the opposite bottom hinge. (Fig. 2)
6. Unscrew and transfer the door adapter (9) and/or
lock catch (8) to the top designated positions of the
door. (Fig. 3)
7. Rotate the door 180° and relocate it to the
designated position. Then screw the bottom hinges
on the designated positions and tighten them. (Fig. 5)
Code Rev. E 20240815 (IEC)
2
6
3
4
2
1
5
5
6
7
8
9
2
3
1
3
2
5
8. Recheck and adjust the door alignment by
loosening the screws (10) and moving the door
adapter (9). Tighten the screws (10) after the door
is levelled. (Fig. 5)
DESIGN 4 – For vertical double door models
1
1
11
4
1.
Remove the right bottom hinge (1) by unscrewing
the four screws (2). Be careful to hold the lower
glass door (3) firmly after removing the screws.
And then gently pull down to remove the lower
glass door from the middle hinge and place it on a
padded surface to avoid the risk of damage. (Fig.
1)
2.
Unscrew and transfer the door adapter (7) and (10)
to the designated opposite position of lower glass
door. At the same time unscrew and transfer hinge
pin (5) of the left bottom hinge (4) included in the
10
fittings. (Fig. 2 & 3)
3.
Remove the door adapter (16) by unscrewing the
two lock screws (15). Be careful to hold the upper
glass door firmly after removing the screws. And
then gently pull down to remove the upper glass
door (17) from the top hinge and place it on a
padded surface to avoid the risk of damage. Then
remove the right top hinge (12). (Fig. 5 & 4)
4.
Unscrew and transfer the middle hinge (14) and the
middle fixing plate (13) to the opposite position. (Fig. 5)
5.
Pop out the cover caps on the left side of cabinet
and use them to
hand side.
6.
Screw the alternative left top hinge (11), included
in the fittings,
4)
7.
Relocate the door adapter (16) on the middle
hinge.
8.
Set the upper glass door to the designated
position and install the two lock screws to connect
the door adapter (16) with the upper glass door
and tighten them before the door is leveled.
9.
Set the lower glass door to the designated position.
Then screw the left bottom hinge on the left
designated position and tighten them
10. Recheck and adjust the lower door alignment by
11
4
3
5
2
6
2
3
5
cover the screw holes on the right
on the left hand side of cabinet. (Fig.
9
10
7
8
Publicité
