Publicité
MENU TREE
The Menu Tree below shows how to navigate through
the TQi transmitter's various settings and functions.
Press and hold MENU to enter the Menu Tree, and use
the following commands to navigate through the menu
and select options.
MENU: When you enter a menu, you always start at the
top. Press MENU to move down the Menu Tree.
When you reach the bottom of the tree, pressing
MENU again will return you to the top.
SET:
Press SET to move across the Menu Tree and select
options. When an option is committed to the
transmitter's memory, the status LED will rapidly
blink green.
BACK: Press both MENU and SET to go back one level in
the Menu Tree.
EXIT:
Press and hold MENU to exit programming.
Your selected options will be saved.
ECHO: Press and hold SET to activate the "echo" function.
Echo will "play back" your current position on the
Menu Tree should you lose your place. For example:
If your current position is Steering Channel End
Points, holding SET will cause the LED to blink green
twice, green once, and then red three times. Echo
will not alter your adjustments or change your
position in the programming sequence.
Below is an example of how to access a function in the Menu
Tree. In the example, the user is setting the Multi-Function knob
to be a Steering % (Dual-Rate) control.
To set the Multi-Function knob to control STEERING % (DUAL-RATE):
1. Switch the transmitter on.
2. Press and hold MENU until the green LED lights. It will blink in single
intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering
Sensitivity (Expo) has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to
indicate Steering % (Dual-Rate) has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Restoring Factory Defaults:
Transmitter
Hold both
Transmitter
Release MENU and SET
OFF
MENU and SET
ON
*Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).
Enter Programming
Press and hold
MENU for 3 seconds
1
Multi-Function Knob
One Blink Green
Press
MENU
2
Channel Setup
Two Blinks Green
Press
MENU
3
Mode Selection
Three Blinks Green
Press
MENU
4
Traxxas-Link
Four Blinks Green
Press SET to clear settings. LED will turn
red LED blinks
solid green. Transmitter is restored to default
www.modellmarkt24.ch
Press MENU to move through options.
Press SET to select an option.
1
Steering Sensitivity (Expo)
One Blink Red
2
Throttle Sensitivity (Expo)
Two Blinks Red
3
Steering % (Dual-Rate)
Three Blinks Red
4
Braking %
Four Blinks Red
Press
5
Throttle Trim
SET
Five Blinks Red
6
Knob Disabled
Six Blinks Red
7
Torque Control*
Seven Blinks Red
8
TSM
Eight Blinks Red
1
Steering (Channel 1)
Press
SET
One Blink Green
Press MENU
2
Throttle (Channel 2)
Two Blinks Green
Press SET to select an option.
1
Electric
Press
SET
One Blink Red
Press MENU
2
Nitro
Two Blinks Red
1
Model Locking
Press
SET
One Blink Green
Press
MENU
2
Delete Model
Two Blinks Green
TQ
i
ADVANCED TUNING GUIDE
Note: The transmitter is "live" during programming
so you can test the settings real time without having
to exit the Menu Tree.
Press MENU to move through options.
Press SET to select an option.
1
Servo Reversing
Press SET to reverse
servo direction.
One Blink Red
2
Sub-Trim
Use knob to adjust
sub-trim. Press SET to save.
Two Blinks Red
3
End Points
Use steering wheel to
adjust. Turn right to desired
Three Blinks Red
end point, press set to save.
Turn left to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.
4
Reset End Points
Press SET to restore factory
default end points.
Four Blinks Red
Press
1
Servo Reversing
SET
Press SET to reverse
servo direction.
One Blink Red
2
Sub-Trim
Use knob to adjust sub-
Press
trim. Press SET to save.
Two Blinks Red
SET
3
End Points
Use trigger to adjust. Pull
back to desired end point,
Three Blinks Red
press set to save. Push
forward to desired end point and press set to save.
To reset max throw: Let go of controls and press SET.
4
Reset End Points
Press SET to restore factory
default end points.
Four Blinks Red
1
Press
Unlock
SET
One Blink Red
2
Lock
Two Blinks Red
3
Unlock All
Three Blinks Red
Press
1
C on rm Deletion
SET
One Blink Red
Publicité
