Publicité
Steering and Throttle End Points
The TQi transmitter allows you to choose the limit of the servo's travel
range (or its "end point") independently for left and right travel (on the
steering channel) and throttle/brake travel (on the throttle channel).
This allows you to ne-tune the servo settings to prevent binding
caused by the servo moving steering or throttle linkages (in the case
of a nitro model) farther than their mechanical limits. The end point
adjustment settings you select will represent what you wish to be the
servo's maximum travel; the Steering Percentage or Braking Percentage
functions will not override the End Point settings.
Steering and Throttle Sub-Trim
The Sub-Trim function is used to precisely set the neutral point of the
steering or throttle servo in the event that simply setting the trim knob
to "zero" does not completely center the servo. When selected, Sub-Trim
allows ner adjustment to the servo output shaft's position for precise
setting of the neutral point. Always set the Steering Trim knob to zero
before making nal adjustment (if required) using Sub-Trim. If Throttle
Trim has been previously adjusted, the Throttle Trim will need to be
reprogrammed to "zero" before making nal adjustment using Sub-Trim.
TRANSMITTER LED CODES
LED Color / Pattern
Solid green
Slow red (0.5 sec on / 0.5 sec o )
Flashing fast green (0.1 sec on / 0.15 sec o )
Flashing medium red (0.25 sec on / 0.25 sec o )
Flashing fast red (0.125 sec on / 0.125 sec o )
Programming Patterns
or
Counts out number (green or red), then pauses
x
8
Fast green 8 times
x
8
Fast red 8 times
RECEIVER LED CODES
LED Color / Pattern
Solid green
Slow red (0.5 sec on / 0.5 sec o )
Flashing fast red (0.125 sec on / 0.125 sec o )
Setting Lock
Once you've adjusted all of these settings the way you like them, you
may want to disable the Multi-Function knob so none of your settings
can be changed. This is especially handy if you operate multiple vehicles
with a single transmitter via Traxxas Link
Multiple Settings and the Multi-Function Knob
It is important to note that settings made with the Multi-Function
knob are "overlaid" on top of each other. For example, if you assign the
Multi-Function to adjust Steering Percentage and set it for 50%, then
reassign the knob to control Steering Sensitivity, the transmitter will
"remember" the Steering Percentage setting. Adjustments you make to
Steering Sensitivity will be applied to the 50% steering throw setting
you selected previously. Likewise, setting the Multi-Function knob to
"disabled" will prevent the knob from making further adjustments, but
the last setting of the Multi-Function knob will still apply.
Name
Notes
Normal Driving Mode
See page 15 for information on how to use your transmitter controls.
Binding
See page 16 for more information on binding.
Turn the Multi-Function knob right or left until the LED stops ashing.
Throttle Trim Seek Mode
See page 30 for more information.
Low Battery Alarm
Put new batteries in the transmitter. See page 13 for more information.
Transmitter and receiver are no longer bound. Turn the system o and then
Link Failure / Error
back on to resume normal operation. Find source of the link failure (i.e., out of
range, low batteries, damaged antenna).
Current menu position
See Menu Tree for more information.
Menu setting accepted (on SET)
Menu SET invalid
User error, such as trying to delete a locked model.
Name
Notes
Normal Driving Mode
See page 15 for information on how to use your transmitter controls.
Binding
See page 16 for more information on binding.
Consistent low voltage in the receiver triggers Fail-Safe so there is enough
Fail-Safe / Low Voltage Detect
power to center the throttle servo before it completely loses power.
www.modellmarkt24.ch
TQ
i
ADVANCED TUNING GUIDE
™
Model Memory.
Failsafe
Your Traxxas radio system is
equipped with a built-in failsafe
function that returns the throttle
to its last saved neutral position in
the event of a signal loss. The LED
on the transmitter and the receiver
will rapidly ash red.
X-MAXX • 31
Publicité
