Graef batessa Instructions D'utilisation page 23

AUTOMATIC SWITCHING OFF
To save energy, the unit turns off after approximately 30 minutes when not in use (Regulation of the EU Commission).
MAKING MILK FROTH
Switch on the unit. The unit is heating up.
●
If "GRAEF" appears on the display, the unit is ready for operation.
●
Fill half of the supplied milk jug with milk. Make sure that it is at refrigerator temperature.
●
Direct the steam lance toward the drip tray.
●
Turn the rotary knob so that it is open and allow the condensation water to escape.
●
Turn the rotary knob so that it is closed again.
●
Turn the steam lance outwards and place the steam lance in the milk jug.
●
Check to see that the steam nozzle is just below the surface of the milk.
●
Turn the rotary knob so that it is open.
●
You will have achieved the right position if you can hear kind of a "sip noise".
●
This might suspend for a short time, because the surface of the milk is moving. You are in the draw phase.
●
Slowly lower the milk jug as soon as the level rises.
●
Once the volume has increased as desired, enter the roll phase.
●
Guide the milk jug upwards so that the nozzle is completely immersed in the milk.
●
Now hold the milk jug as still as possible.
●
Place one hand flat against the milk jug.
●
The milk should swirl without drawing in any more air.
●
If air is drawn in again, change the position of the steam nozzle slightly.
●
The milk foam has reached the right temperature when the side of the milk jug becomes too hot to hold.
●
Turn the rotary knob so that it is closed.
●
IMPORTANT!
Remove the steam lance from the milk only after turning the rotary knob so that it is closed.
Now remove the steam lance from the milk.
●
After making the milk froth, hit the milk jug briefly onto the table top in order to remove the last coarse air bubbles. Swivelling is also helpful
●
to distribute the froth evenly.
Clean the steam lance immediately afterwards to avoid milk incrustations.
●
A short burst of steam is enough to blow the milk residue out of the nozzle. Clean the outside of the nozzle with a damp cloth. Caution, the
●
steam lance gets hot.
IMPORTANT!
To practise it, you can use the following method:
Pour cold water into the milk jug.
●
Add a drop of detergent.
●
Froth it up as described above.
●
If you carry out the frothing process correctly, the mixture will look like real milk foam.
●
Please do not drink this mixture!!
DESCALING REMINDER
The factory setting for the descaling function recall is set to 25 L. After 25 litres have been used, "KALK" flashes on the display. You can continue
to use the unit as usual, but "KALK" will continue to appear on the display. Only after a complete decalcification of the two circuits, the "KALK"
display goes off on the display (for this, see the "Descaling" chapter). The number of liters can be changed according to the use and hardness
of your water.
12 L = (In hard water areas with more than 15°dH)
25 L = (In mild water areas with 7,3°dH up to 14°dH)
50 L = (n soft water areas with up to max. 7,3°dH)
You can ask for your exact water hardness at the local waterworks. To find out how to change the number of litres, see page 14 under "DES-
CALING REMINDER".
DESCALING
Regularly perform a decalcification, at the latest when "Kalk" appears on the display. All circuits must be descaled. We recommend to use
Graef descaling tablets. You can obtain them in our online shop at www.graef.de under
item No. 145618 or from your specialist dealer.
DE
EN
FR
NL
IT
PL
23