Parkside PBKS 53 A2 Consignes D'utilisation Et De Sécurité page 15

m WARNING
Avoid direct skin contact with fuel and inhalation of fuel va-
pours.
Use only a mixture of unleaded petrol (min. RON 95) and
special 2-stroke engine oil (JASO FD/ISO - L - EGD). Mix the
fuel mixture as per the fuel mixing table.
Put the correct amount of petrol and 2-stroke oil into the en-
closed mixing bottle (30) (see "Fuel mixing table"). Then
shake the mixing container (30) well.
8.1.1 Fuel mixing table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol ..................................................2-stroke oil
0.5 litres ....................................................12.5 ml
8.2 Filling with fuel
m WARNING
Only fill the fuel when the engine is switched off and has
cooled down. There is a risk of fire!
• Always clean the area around the fuel tank cap (13) before
filling to prevent dirt from falling into the fuel tank. Use a dry,
lint-free cloth for this purpose.
• Lay the device on its side with the fuel tank cap (13) facing
upwards.
• Turn the fuel tank cap (13) anti-clockwise and open it. The
fuel tank cap (13) is connected to an anti-loss device in the
fuel tank and thus cannot fall off.
• Pour the fuel mixture into the fuel tank. Do not spill fuel when
refuelling and do not fill the fuel tank to the brim.
• Wipe up spilled fuel immediately.
• Turn the fuel tank cap (13) clockwise to close it.
NOTE
Also check the chain oil after each fuel fill.
8.3 Filling with chain oil
m WARNING
Only fill the saw chain oil when the engine is switched off and
has cooled down. There is a risk of fire!
Never work without chain lubrication! If the saw chain runs
dry, the cutting gear will be irreparably destroyed in a short
time.
Always check chain lubrication before working.
NOTE
Use only saw chain oil. Preferably biodegradable. Do not use
waste oil, engine oil, etc.
Check during work that the chain lubrication is working.
• Always clean the area around the chain oil fuel cap (14)
before filling so that no dirt falls into the chain oil tank. Use
a dry, lint-free cloth for this purpose.
• Lay the device on its side with the chain oil fuel cap (14) is
facing upwards.
• Turn the chain oil fuel cap (14) anti-clockwise and open
it. The chain oil fuel cap (14) is connected to an anti-loss
device in the chain oil tank and thus cannot fall off.
10 GB/IE/NI/CY/MT
• Pour the supplied bio chain oil into the chain oil tank. Do
not spill chain oil when refuelling and do not fill the chain
oil tank to the brim.
• Wipe up spilled chain oil immediately.
• Turn the chain oil fuel cap (14) clockwise to close it.
8.4 Tensioning and checking the saw chain
m WARNING
Put on protective gloves! Danger of injury due to
the sharp cutting teeth!
Check the chain tension regularly before each start-up.
• Before tensioning, loosen the two fixing nuts (20) a little
with the spark plug wrench (31).
• Turn the chain tensioning screw (21) clockwise with the slot-
ted screwdriver (31) to increase the tension.
• Tighten the two fixing nuts (20) with the spark plug wrench
(31).
• The saw chain (17) must be in contact with the underside
of the guide rail. Check whether the saw chain (17) can be
pulled over the guide rail (16) by hand (with the chain brake
released, pull the front hand guard (1) back).
NOTE
A new saw chain (17) stretches and needs to be re-tensioned
more often.
9. Commissioning
m CAUTION
Please observe the legal provisions from the noise protection
ordinance.
Working instructions
Familiarise yourself with handling the chainsaw before use.
It is mandatory to check the chainsaw carefully for any dam-
age before each use or after it has fallen down.
If any damage is found, it must be repaired immediately by
you or an authorised service centre. Check the following
points before commissioning the chainsaw:
• Correct fit of the guide rail
• Installation/running direction, as well as faultless (sharp)
saw chain
• Tension of the saw chain (check and readjust several times
with a new chain)
• Chain lubrication function
• Chain brake function
• Function of the clutch (no chain movement in neutral)
• Check the fuel system for leakage
• Faultless condition and completeness of the guards and the
cutting device
• Tight fit of all screw connections
• Smooth running of all moving parts
NOTE
The chainsaw does not have a starting gas lock.