Parkside PBKS 53 A2 Consignes D'utilisation Et De Sécurité page 14

■ Adhere to the instructions of the manufacturer when sharp-
ening and maintaining the saw chain. If the depth limiter is
too low, this increases the tendency towards kickback.
■ Do not saw with the tip of the guide bar. There is a risk of
kickback.
■ Make sure that there are no nails or metal pieces in the cutting
area. Pay special attention to nails or pieces of iron around
the cutting area. Also be careful when sawing hardwoods
where the chain can get caught. This can cause kick-back.
■ Start cutting at full power and always keep the chainsaw at
maximum speed while sawing.
■ Make sure that there are no objects on the floor that you
can trip over.
6.10 Residual risks
m DANGER
RISK OF INJURY !
Contact with the saw chain can lead to fatal cuts.
Never touch the saw chain with your hands while it is running.
RISK OF KICK-BACK !
Kick-back can lead to fatal cuts.
DANGER OF BURNING !
The chain and guide bar heat up during operation.
7. Technical data
Weight unfuelled, without cutting gear ............. approx.5.6 kg
Weight unfuelled, with cutting gear ................. approx. 6.8 kg
Fuel tank .............................................approx. 550 cm
Tank for chain lubricating oil ............approx. 260 cm
Usable cutting length* .......................................................44 cm
Guide rail ................................................................. 52 cm (18")
Max. chain speed ......................................................... 22.1 m/s
Chain pitch .................................................... 8.25 mm (0.325")
Driving link thickness .......................................1.5 mm (0.059")
Type of saw chain ...................................................KANGXING
(pre-assembled): ..................................................... 325-058-72
Type of guide bar ...................................................KANGXING
(pre-assembled): ...............................................BE18-72-5810P
Chain wheel tooth pitch .............7 teeth / 8.255 mm (0.325")
Engine displacement........................................................ 53 cm
Max. engine power output per ISO 7293 ....................2.0 kW
Idle speed n ....................................................3100 ± 300 rpm
0
Speed n ................................................................ 11,500 rpm
max
Spark plug .......................................................................... L8RTC
* The actual cutting length may be less than the specified cut-
ting length.
Noise
Sound pressure level L per ISO 22868 .....................98.3 dB
pA
Uncertainty K .................................................................... 3 dB
pA
Sound power level L
WA
per ISO 22868 ..............................................................117.0 dB
Uncertainty K ................................................................... 3 dB
WA
Information on noise emission in accordance with the Product
Safety Act (ProdSG) or EC Machinery Directive: The noise
pressure level at the workplace can exceed 80 dB.
In this case, noise protection measures for the operator are
required (e.g. wearing suitable and designated hearing pro-
tection and taking regular breaks).
Vibration
Vibration value at the rear
Handle per ISO 22867 ................................................6.4 m/s
Vibration value at the front
Handle per ISO 22867 ..............................................6.69 m/s
Uncertainty K ................................................................. 1.5 m/s
m WARNING
Avoid the risks associated with vibration, e.g. the risk of white
finger syndrome (circulatory disorders) by taking frequent
breaks from work where you rub your palms together, for ex-
ample.
m WARNING
The actual vibration emission value during use of the machine
may differ from the vibration emission value indicated in the
operating manual or by the manufacturer. This can be caused
by the following influencing factors to which attention should
be paid both before and during every use:
• Is the machine being properly used
3 (0.55 l) • Is the nature of the cutting or processing of the material
(0.26 l) correct
3
• Is the machine in good working order
• Sharpness of the cutting tool and is the cutting tool the cor-
rect one
• Are the handles or, if applicable, the optional anti-vibration
handles installed and firmly attached to the body of the ma-
chine.
8. Before commissioning
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the packaging
and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport dam-
3
age.
• If possible, keep the packaging until the expiry of the war-
ranty period.
ATTENTION
The device and the packaging are not children's toys! Do not
let children play with plastic bags, films or small parts! There is
a danger of choking or suffocating!
• Remove the quick start guide from the start pull cord (4).
8.1 Mixing fuel
The engine must be operated with a fuel mixture of petrol and
engine oil.
2
2
2
GB/IE/NI/CY/MT 9