Milwaukee M18 FDGROVB Notice Originale page 8

Masquer les pouces

page de 67

/ 67
Signets

Les langues disponibles

ONE KEY

3V CR2032

Coin Cell

Knopfzelle

Batterie bouton

Batteria a bottone

Célula de botón

Knopfzelle

Knoopcel

Knapcelle

Knappcelle

Knappcell

Nappiparisto

Κερματοειδής μπαταρία

Düğme pil

Knoflíkový akumulátor

Gombíkový akumulátor

Ogniwo guzikowe

Gombelem

Gumbasta baterija

Ćelija

Podziņelements

Diskinis galvaninis elementas

Nööpelement

Миниатюрный элемент питания

Плоска батерия

Baterie tip nasture

Батерија тип копче

Мініатюрний елемент живлення

‫بطارية كالزر‬

TECHNICAL DATA

Type

Production code

Battery voltage

Frequency band(s) of Bluetooth

Radio-frequency power

Bluetooth version

Rated speed

Collet diameter

Accessory Abrasive grinding body diameter max.

Accessory Diameter max.

Weight according EPTA-Procedure 01/2014

(Li-Ion 2,0 Ah ... 12,0 Ah)

Recommended Ambient Operating Temperature

Recommended battery types

Recommended charger

Noise information Measured values determined according

to EN 60745.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level / Uncertainty K

Sound power level/ Uncertainty K

Vibration information Vibration total values (triaxial vector

sum) determined according to EN 60745

Vibration emission value a

/ Uncertainty K

WARNING!

The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in

EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibra-

tion and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the

total working period.

An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it

is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the acces-

sories, keep the hands warm, organization of work patterns.

WARNING!

Read all safety warnings, instructions,

illustrations and specifications provided with this power tool. Failure

to follow all instructions listed below may result in electric shock, fire

and/or serious injury.

Save all warnings and instructions for future reference.

DIE GRINDER SAFETY WARNINGS

a) Safety warnings common for grinding:

b) This power tool is intended to function as a grinder. Read all

safety warnings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious

injury.

c) Operations such as sanding, wire brushing, polishing or

cutting-off are not recommended to be performed with this

power tool. Operations for which the power tool was not designed

may create a hazard and cause personal injury.

d) Do not use accessories which are not specifically designed

and recommended by the tool manufacturer. Just because the

accessory can be attached to your power tool, it does not assure

safe operation.

e) The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Accessories

running faster than their rated speed can break and fly apart.

f) The outside diameter and the thickness of your acces-

sory must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or

controlled.

M18 FDGROVB

M18 FDGROVPDB

Die Grinder

4918 20 01 XXXXXX MJJJJ

4918 30 01 XXXXXX MJJJJ

18 V ⎓

2402-2480 MHz

1,8 dBm

4,2 BT signal mode

n 8.000-20.000 min

-1

6 / 8 mm

50 mm

76 mm

1,7 ... 2,8 kg

-18 ... +50 °C

M18B...; M18HB...

M12-18...; M18DFC, M1418C6

79,3 dB (A) / 3,0 dB (A)

90,3 dB (A) / 3,0 dB (A)

12,4 m/s

/ 1,5 m/s

9,9 m/s

g) The arbour size of wheels, sanding drums or any other

accessory must properly fit the spindle or collet of the power

tool. Accessories that do not match the mounting hardware of the

power tool will run out of balance, vibrate excessively and may

cause loss of control.

h) Mandrel mounted wheels, sanding drums, cutters or other

accessories must be fully inserted into the collet or chuck. If

the mandrel is insufficiently held and/or the overhang of the wheel is

too long, the mounted wheel may become loose and be ejected at

high velocity.

i) Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

sanding drum for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory and

run the power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this test time.

j) Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As

appropriate, wear dust mask, hearing protectors, gloves and

workshop apron capable of stopping small abrasive or work-

piece fragments. The eye protection must be capable of stopping

flying debris generated by various operations. The dust mask or

respirator must be capable of filtrating particles generated by your

operation. Prolonged exposure to high intensity noise may cause

hearing loss.

ENGLISH