Scheppach BC-MP320-X Traduction Du Mode D'emploi Original page 24

Vibration parameters
Vibration a
h
Measurement uncertainty K
The total vibration emission values specified and the de-
vice emissions values specified have been measured in
accordance with a standardised test procedure and can
be used for comparison of one electric tool with another.
The total noise emission values specified and the total vi-
bration emission values specified can also be used for an
initial estimation of the load.
WARNING
The noise emission values and vibration emis-
sion value can vary from the specified values
during the actual use of the power tool, de-
pending on the type and the manner in which
the electric tool is used, and in particular the
type of workpiece being processed.
Try to keep the stress as low as possible. For example:
Limit working time. In doing so, all parts of the operating
cycle must be taken into account (such as times in
which the power tool is switched off or times in which it
is switched on, but is not running under a load).
7 Unpacking
WARNING
The product and the packaging material are not
children's toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suffo-
cating!
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. Immediately report any damage to the trans-
port company that delivered the Product. Later claims
will not be recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
• When ordering please provide our article number as
well as type and year of manufacture for the product.
24 | GB
8 Assembly
2
< 2.5 m/s
CAUTION
2
1.5 m/s
Danger of injury!
Do not insert the battery until the battery-powered tool
is ready for use.
CAUTION
Danger of injury due to rotating blade. Only work on the
product when the blade is switched off and stationary!
ATTENTION
Always make sure the product is fully assembled
before commissioning!
ATTENTION
Ensure that the cable is not squeezed during assembly.
8.1 Installation of the lower push bar
(3) (Fig. 3)
1. Fit the two lower push bars (3) in the holes (3b) pro-
vided.
2. Fasten each of these with a Phillips screw (3a).
8.2 Installation of the upper push bar
(1) (Fig. 1, 4)
1. Screw the upper push bar (1) to the lower push bars
(3) with one flat head screw (2a) and a locking nut (2)
on each side.
8.3 Fitting the cable holder (8) (Fig. 1, 5)
1. Clip the two cable holders (8) into the upper push bar
(1) and lower push bar (3) and secure the cable (9).
8.4 Grass collection basket
8.4.1
Note:
The carry handle must be fitted on the upper side, where
the fill level indicator is also located.
1. Attach the carrying handle (5a) of the grass collection
bag (5) to the holder provided on the top of the grass
collection bag (5).
2. Screw the carry handle (5a) firmly to the inside of the
grass collection basket (5) with two screws (5b).
8.4.2
WARNING
Danger of crushing!
Pay attention to your fingers!
• Wear gloves.
1. Clip both parts of the grass collection bag (5) together.
www.scheppach.com
Fit the carry handle (5a) to the grass
collection basket (5) (Fig. 1, 6)
Mount the grass collection basket (5)
(Fig. 6)