Emerson AVENTICS EtherCAT Notice D'instruction page 17

Ambient conditions
• Protect the product from direct sunlight and UV radiation.
6.1.2 Required accessories, materials and tools
Select material and tools that are suitable for your product configuration. De-
pending on the configuration, you will need further accessories.
Mounting material
Tools
• 1x Torx 10 screwdriver
6.2 Preparation
6.2.1 Unpacking and checking the product
1. Check the material number to see if the product matches your order.
2. Check the product for transport and storage damage.
Do not install a damaged product. Return damaged products together with
the delivery documents. See
3. Prepare required accessories, materials and tools.
6.2.2 Implementing safety measures
Procedure
1. Do not carry out any work on the system during preparation.
2. Close off dangerous areas.
3. Make sure the system or system part is not under pressure or voltage.
4. Protect the system against being restarted.
5. Allow product and adjacent system parts to cool down.
6. Wear PPE.
6.2.3 Software installation
1. Call up the product page in the Emerson Store: http://www.emerson.com/
xv03c | http://www.emerson.com/xv05c
There is a QR code on the product that also leads to the software and user docu-
mentation.
2. Download zip archive with device description files.
Convention for naming the installation file with the date of issue:
ESI-Vx_xx-Aventics-1B2-XVE-yyyyddmm.xml
3. Install files.
6.3 Installation
The product is preassembled. See
6.4 Connecting the electrical system
• Observe the pin assignment. See
• Observe technical data on the cable cross-section. See
• Use shielded cables to protect against interference and electrostatic effects.
• Ensure that X7E1 and X7E2 are not connected to the same switch or hub.
• Ensure that no ring topology is manufactured without a ring master.
AVENTICS™ EtherCAT | 570089-BAL-AA | English
g 4.3 Returning the product.
g 10. Disassembly and exchange.
g 11.2 Pin assignment.
g 14 Technical
Procedure
1
Fig. 3: Grounding screw position
1 Grounding screw
1. Release the grounding screw.
2. Mount the grounding cable using the grounding screw. Screw in grounding
screw.
3. Connect the bus cable to the plug connector X7E1 or X7E2.
Tightening torque: 1.5 Nm + 0.5 Nm
4. Connect the voltage to the plug connector X1S.
Tightening torque: 1.5 Nm + 0.5 Nm
5. Close off all unused ports.
7 Commissioning
7.1 Preparation
General requirements
Implement safety measures. See
u
Make sure that all connections are in perfect condition.
u
Check LED. See g 11.1 Display.
u
7.1.1 Setting parameters
1. Load the ESI file in the PLC configuration program.
2. If the PLC is not compatible with the ESI file: Download and use an older ver-
sion of the ESI file.
ð Available parameters are displayed via the configuration file in the PLC
configuration program.
3. Adjust the parameters of the individual modules in the PLC configuration pro-
data.
gram.
ð Parameters and configuration data are sent from the PLC to the product when
the product is switched on.
Parameters for diagnostic messages
Type of message
Diagnosic Enable/Dis-
able - Global
Deactivated (default)
Activated
Table 1: Diagnostic messages
Message type Index
Manufacturer-spe- 0x2100
cific
g 6.2.2 Implementing safety
Index Subindex
0x2010 0x00
0x01
Diagnosis is not reported to the PLC.
Diagnosis is reported to the PLC.
Subindex
0x00
0x01
measures.
Error description
Number of entries in
the index
Activate/deactivate
diagnosis
Error description
Supply voltage UL < 18 V
Supply voltage UL
> 26.4 V
Valve supply voltage UA
< 21.6 V (UA ON)
17