Bosch 0601B47000 Notice Originale page 40

40 | English
Adjusting mitre angles
Setting Standard Mitre Angles (see figure J)
For quick and precise setting of commonly used mitre
angles, detents (27) are provided on the saw table:
Left
0°
45°; 31.6°; 22.5°; 15°
– Loosen the locking knob (22) if it is tightened.
– Pull the lever (23) and rotate the saw table (17) left or
right to the required detent.
– Release the lever again. The lever must be felt to engage
in the detent.
– Retighten the locking knob (22).
Setting Any Mitre Angle (see figure K)
The mitre angle can be set between 52° (left-hand side) and
60° (right-hand side).
– Loosen the locking knob (22) if it is tightened.
– Pull the lever (23) and at the same time press the locking
clamp (21) until this clicks into the slot provided for it.
This means the saw table can now move freely.
– Turn the saw table (17) left or right by the locking knob
until the angle indicator (26) shows the required mitre
angle.
– Retighten the locking knob (22).
– To loosen the lever (23) again (for setting standard mitre
angles), pull the lever upwards.
The locking clamp (21) springs back into its original posi-
tion and the lever (23) can click back into the detents
(27).
Adjusting bevel angles
For bevel cuts when using the SDS bolt (63), before
u
sawing, first make sure that the SDS bolt cannot come
User interface and connectivity functions
User interface
The user interface (37) is used to preselect the speed, to
turn the laser and worklight on and off and to indicate the
status of the power tool.
Note: The speed preselection button (56) and the laser/
worklight on/off button (54) are active when the power tool
is switched off or running at no-load.
ECO mode
If the power tool is operated in the energy-saving ECO mode,
the battery life may be up to 20% longer.
If the ECO mode is active, the symbol E is shown on the
speed setting/mode indicator (55). In addition, the ECO
mode indicator (50) lights up.
1 609 92A 8KY | (07.03.2023)
The bevel angle can be set between 47° (left side) and 47°
Right
(right side).
For quick and precise setting of frequently used bevel
angles, stops have been provided for the angles 0°, 22.5°,
15°; 22.5°; 31.6°; 45°; 60°
33.9°, 45° and 47°.
Setting standard bevel angles (see figure M)
– Standard 0° bevel angles:
– Standard 45°, 33.9° and 22.5° bevel angles:
– Standard 47° bevel angles:
Setting the Complete Bevel Angle Range (see figure L)
– Pull the stop (43) all the way forward.
– Pull the right-hand adjustable fence (16) all the way out
– Loosen the clamping handle (34).
– Swing the tool arm left or right by the handle (9) until the
– Retighten the clamping handle (34).
Speed preselection
An ECO mode and three speed settings are preset.
The values for materials in the table are recommendations.
When sawing at a factory preset speed, the speed setting/
mode indicator (56) lights up white.
You can use the button for speed preselection (56) to set
the speed, even during operation.
When sawing at an individually set speed, the speed setting/
mode indicator (56) lights up blue.
into contact with the surface of the workpiece at any
time by making a suitable adjustment to the depth
stop (35). This prevents damage to the SDS bolt and/or
the workpiece.
Swing the tool arm by the handle (9) slightly to the left
and push the stop (43) all the way back.
Turn the left-hand or right-hand stop (31) until the re-
quired standard bevel angle engages at the arrow mark.
Swing the tool arm by the handle (9) slightly to the left
and push the stop (43) all the way forward.
This enables you to use the complete bevel angle range
(left and right).
or remove it completely.
If you want to use the entire bevel angle range, you also
have to pull the left-hand adjustable fence (16) all the
way out or remove it completely.
angle indicator (41)/(33) shows the required bevel
angle.
Speed setting Speed [min
Eco 2500
1 3000
2 3800
3 4500
-1
] Material
Aluminium
Plastic or PVC
Wood
Bosch Power Tools