Eurocave Vin au Verre 8.0 Mode D'emploi page 22

3. MAINTENANCE
If you have not taken out a maintenance contract with your EuroCave
Professional exclusive distributor, it is essential to carry out checks
and maintenance every 6 months in order to ensure the longevity
of your appliance. Make enquiries with your EuroCave Professional
stockist to have preventative maintenance carried out on your
appliance.
OPERATING FAULTS
VI
& WARNING MESSAGES
Visual warnings and possible faults Causes
A/ The nitrogen
cylinder is not open
6°C 18°C
B/The nitrogen
NITROGEN EMPTY
MESSAGE D'ALERTE
cylinder is empty
3cl 6cl 12cl
C/The nitrogen
cylinder is not
correctly connected
A wine bottle is not
correctly connected to
the machine
6°C 18°C
or
A bottle connector
NITROGEN LEAK
MESSAGE D'ALERTE
3cl 6cl 12cl
socket is in the vertical
position without a
bottle
A wine bottle is not
correctly connected to
the machine
6°C 18°C
or
several changes have
SLOW NITROGEN LEAK
MESSAGE D'ALERTE
3cl 6cl 12cl
been made without
using the bottle
changing menus.
Empty wine bottle
6°C 18°C
BOTTLE X EMPTY
MESSAGE D'ALERTE
3cl 6cl 12cl
The measure
requested is larger
than the volume
6°C 18°C
remaining in the bottle.
EN
VOLUME OF BOTTLE X INSUFFICIENT
MESSAGE D'ALERTE
3cl 6cl 12cl
-20-
Any work on the refrigerating unit must be carried out by
a qualified refrigerationist, who must perform leak tests
on the circuit before restarting. In the same way, any work
carried out on the electrical system must be carried out by a
qualified electrician.
Corrective action
Click the warning message. Check whether the cylinder is open or closed.
Open the nitrogen cylinder if it is closed.
If it is already open, refer to cause B or C
Close the cylinder and replace it (see Chapter III.3)
Check connection of the tube to the nitrogen cylinder.
Click the warning message.
Check each neck of the bottles connected to the
machine.
Contrôler
– Bottle necks not chipped,
les 8 bouteilles
connectées à la
– Upper part of the neck free from any foreign body
machine
(cap, cork)
Check the position of each bottle connector socket
The bottle connector socket must remain in an
Contrôler
inclined position: if it is in a vertical position without
la position de
chaque tête de
mise sous vide a bottle, this will cause nitrogen to leak.
Contact customer service if the problem continues
Contact
Contacter SAV
customer service
Click the warning message.
This warning is not disabling, you can continue to use the appliance normally,
but it is essential that you resolve the leak quickly to prevent excess nitrogen
consumption.
Check each neck of the bottles connected to the
machine.
– Bottle necks not chipped,
Contrôler – Upper part of the neck free from any foreign body
les 8 bouteilles
connectées à la (cap, cork)
machine
If several changes have been made without using the
bottle changing menus, this can cause the message
"Slow leak warning" to appear without there actually
Contact
Contacter SAV
being a leak. In this case, click the warning message
customer service
to make it disappear.
Contact customer service if the problem continues.
Replace it with a new bottle
Select a smaller measure or change the bottle.
The temperature
settings have not been
reached for 24 hrs.
6°C 18°C
TEMPERATURE ALARM
MESSAGE D'ALERTE
3cl 6cl 12cl
Maintenance must be
scheduled
6°C 18°C
3cl 6cl 12cl
A key is displayed on the welcome
screen.
The pressure gauge
may be faulty
6°C 18°C
OVERPRESSURE WARNING
MESSAGE D'ALERTE
3cl 6cl 12cl
Abnormal activity has
been detected on the
Screen cleaning detected screen.
Please finish cleaning and drying, then do not touch the screen
for 30 seconds.
DAILY CLEANING
MONTHLY CLEANING
My wine is no longer pouring The outflow circuit
correctly from a wine dispensing tap may be obstructed
My wine is no longer pouring It may be a measure
correctly from several wine
control fault
dispensing taps
My bottle does not remain in place
The bottle neck or the
correctly in the bottle connector seal may be too damp
socket
The pressure is not equal to 0.6 - The pressure reducer
0.7 bars when I open my nitrogen is not set to the correct
cylinder pressure
FREQUENTLY ASKED
Questions Answers
What should I do if I forget my password? Call your distributor to get your password reset.
Can I flush fit the product? Yes, provided that you observe the flush-fitting conditions.
5 cm at the sides + 10 cm at the back + 5 cm at the top and breather hole
> see flush-fitting diagram (III.2)
Which nitrogen cylinder should I buy? In France, the model is Aligal 1, containing 0.9 m
Outside of France, ask your stockist.
The cylinder must meet the following specifications:
200 bars / 100% food-quality nitrogen
Connection according to country (see page 9)
Where can I purchase more nitrogen? In France, contact your nearest Air Liquide or Linde distributor.
Abroad, contact your stockist.
Are there any equivalents to Aligal? Look for 100% food-quality nitrogen.
Check that the appliance's doors are shut correctly and that the door seals are
pressed firmly against the appliance.
The warning message will disappear once the temperature setting has been
reached.
If the problem continues, contact customer service.
If you currently have a contract (in France), customer service will contact you to
arrange maintenance of your appliance.
At the end of the contract, contact customer service to continue maintenance.
Click the warning message.
0.6 150
Check the pressure level on the pressure reducer.
30
0 0 300 2.5
bar
If the pressure is 0.6 bars – 0.7 bars, follow the
instructions on the screen.
If not, call customer service.
If cleaning is underway, finish cleaning and dry the screen. Wait then return to
the main screen after 30 seconds.
Press the warning to launch daily cleaning. This warning can be set. To set this
warning, please contact your distributor.
Press the warning to launch monthly cleaning. This warning can be set. To set
this warning, please contact your distributor.
Clean the plunge tube filter, carry out thorough rinsing (launch bottle
replacement with another label on the wine dispensing tap) (see IV.1.D).
Clean the plunge tube filters, carry out thorough rinsing.
For all the wine dispensing taps affected, replace the bottle with
another label (see IV.1.D)., then proceed to calibration.
Try again, having dried the seal and the bottle neck. If the problem continues,
contact customer service.
Call customer service.
QUESTIONS
3 (or Aligal 12).
VII
EN
-21-