Télécharger Imprimer la page

Eurocave Vin au Verre 8.0 Mode D'emploi page 20

Masquer les pouces Voir aussi pour Vin au Verre 8.0:

Publicité

Les langues disponibles

Les langues disponibles

D. Replacing a bottle with a different label
When replacing a bottle with another label, you should clean the tube immersed in the bottle.
To do so, take a wine bottle filled with water for rinsing and your new bottle.
1
From the welcome screen, access the Settings Menu
Then select
2
Select the bottle you want
to replace.
3
Select the left pictogram
5
Open your new bottle and
install it where the old one
was, inserting the tube
inside. Push upwards, then
forwards whilst maintain-
ing the bottle in the upper
position.
And validate
Some bottles may need securing. To do so, it is possible to
raise the adjustable bottle support by bringing it into contact
with the bottle, without applying force.
Important: check the condition of the bottle neck before
installing a bottle.
EN
-16-
4
Remove the empty wine
bottle.
Install a wine bottle filled
with water in the connector
socket, ensuring that you
insert the tube into the
bottle.
To do so, push the bottle
upwards, then push for-
wards whilst maintaining
it pushed upwards. Place
a recipient under the wine
Hold an empty
Tenir une
bottle under the
bouteille vide
dispensing tap to collect
wine dispensing
sous le bec
tap
verseur
the rinsing water.
Press one of the measures
and maintain pressure
on the button until the bottle
of water is completely
empty.
Maintain
Maintenir le
pressure on the
Once the bottle of water is
bouton appuyé
button to dry the
pour sécher
circuit
empty, maintain pressure
le circuit
on the button for approxi-
mately 5 seconds to dry the
circuit until the tap stops dripping.
Remove the bottle used for rinsing. Cleaning is complete, you
can install your new label.
6
Indicate the name of the
label and the volume of
the bottle.
LABEL NAME
NOM RÉFÉRENCE
chateau ...
Then validate
BOTTLE VOLUME
VOLUME BOUTEILLE
75
cl
.
If you do not want to replace an empty bottle
immediately, to make the warning message disappear,
go into
or
when entering information
about the bottle, and enter "0" or nothing.
Important:
If you have any doubts, use your Bottle Neck Checker
to check the dimensions of the bottle neck. There are
details about the procedure in chapter IV, subchapter
Installing bottles.
2. SETTING MEASURES
By default, the 3 measures of each Vin au Verre 8.0 wine dispensing tap are set at 3, 6 and 12 cl.
1
From the welcome screen, access the Settings Menu
Enter your "Manager" password and press
Then select
2
x8
x8
Tip: If you want the same setting for the 3 measures of
the 8 wine dispensing taps (example: 3, 6 and 12 cl for the
3 measures of the 8 wine dispensing taps), tick
them in one go.
3. SETTING TEMPERATURES
Important: The temperature of the left compartment (compartment
1) will always be 3°C lower (5°F) than the right compartment
(compartment 2)
1
From the welcome screen, access the Settings Menu
Enter your "Manager" password and press
Then select
.
4. APPLIANCE LIGHTING
From the welcome screen, access the Settings Menu
Enter your "Manager" password and press
For the wine dispensing tap lighting:
Select:
Choose the colour of the lighting by pressing
Then, set the intensity by pressing
And validate
.
Tips:
• Maintain pressure on the arrow to scroll quickly.
• You can opt for the automatic "colours in sequence" option by selecting
The lighting will automatically change from one shade to the next.
• If the arrows for choosing the light intensity and colour are not displayed, this means that the automatic colours in sequence
function is activated. Press
3
3
cl
2
cl
6
3.5
12
cl
6.5
Select the bottle(s) you want
to set the measures for.
Tips:
This indicator light
• The volumes of the measures to be entered must be
indicates that the bottle is
between 1 cl and the total volume of the bottle installed.
selected. Press the indicator
light to deselect it.
• Delete the content of the cell by pressing
entering the value.
Then validate
.
• For the price of the glass, you must round up or down to the
decimal point. Example for €5: enter 5-0-0
• By indicating the price of the glass, you can find out the
consumption and turnover generated by the label in the
to set
Statistics Menu
• If the total amount of the volumes of glasses served is
exactly the same as the volume in the bottle, then splashes
may appear on the last glass of wine served.
The recommended temperature setting ranges are:
– In the left compartment: 6 - 15°C / 43-59°F
– In the right compartment: 9 - 18°C / 48-64°F
2
T1
6
°C
T2 ≥ (T1 + 3°C)
. Then select
For the compartment lighting:
Select:
Choose the colour of the lighting by pressing
Then, set the intensity by pressing
Proceed in the same way for the second compartment
and validate
.
Tip: By selecting
, the lighting choices of the last compartment
set will be applied identically in the other compartment.
.
to disable it.
3 measures can be set for
each
of
the
8
wine
dispensing taps. Indicate
the volume and price per
glass
for
each
of
the
measures.
Then validate
.
before
Set the temperatures of the
T2
two compartments using
and
Then validate
.
18
°C
EN
-17-

Publicité

loading