Eurocave Vin au Verre 8.0 Mode D'emploi page 19

USING
IV
VIN AU VERRE 8.0
1. INSTALLING THE BOTTLES
A. Possible layouts
Check the condition of the bottle neck before inserting a bottle. There
should be no remnants of cap on the bottle neck.
1. You should check any new labels (before buying if possible) with
your Bottle Neck Checker as well as bottles that do not remain in place
correctly in the bottle connector socket.
1
BOTTLE NECK CHECKER
INTERNAL DIAMETER
OK NOT OK NOT OK
min ≥ 17.2mm / 0.68'' - max ≤ 19.7mm / 0.77''
EXTERNAL DIAMETER
OK NOT OK 150 cl
75 cl
max ≤ 32mm / 1.26''
EN
-14-
2. Place the neck of the bottle inside the bottle connector socket guide,
ensuring that you insert the plunge tube inside.
3. Push the bottle upwards until the spring is compressed to the
maximum, then tilt the bottle towards the back of the appliance, whilst
maintaining it pushed upwards.
4. Some bottles may need securing. To do this, it is possible to raise
the adjustable bottle support by bringing it into contact with the bottle,
without applying force.
1
2
~1 cm
Important: If there is no bottle in place, the bottle connector
socket guide must be in an inclined position. A vertical
position with no bottle will cause nitrogen to leak.
1
16 ° C
6 ° C
6cl 15cl
3cl
Important: Magnums must only be installed in the 2 outer
bottle holders of each compartment. You can have
4 magnums in use at the same time.
6 ° C
3cl
150 cl
75 cl
16 ° C
6 ° C 15cl
6cl
3cl
150 cl
75 cl
1
1/4
For bottles having a neck with
2
an external diameter greater
1
than 32 mm, you must remove
the bottle connector socket by
1/4
unscrewing it by a quarter turn
before inserting the bottle.
1
1/4
2
B. Setting bottles
This function allows you:
• to name the bottles in order to analyse sales per label after service.
1
From the welcome screen, access the Settings Menu
Then select
2
3
3
2
It is possible to rename a bottle or change its volume at any time by selecting
1
4
3
The volume must be 1cl - 151 cl for outer bottles and 1 - 100 cl for the 4 inner bottles
~1 cm
(because Magnums are only allowed on the outer parts of the appliance: 2 in each compartment).
2
C. Replacing a bottle with the same label
~1 cm
Vin au Verre 8.0 informs you when you need to replace an empty bottle:
3
• if the appliance's lighting is activated, a "Wine bottle empty" warning message appears on the welcome screen and the wine dispensing tap of the
empty bottle flashes.
• If the appliance's lighting is switched off, a "Wine bottle empty" warning message appears and the picture of the empty bottle flashes on the
welcome screen.
1 4
16 ° C
15cl From the welcome screen, select
6cl
2
3
2
Tip: You can replace a bottle even if the current one is not
completely empty and the indicator light is not flashing. In this
way, by installing a full bottle, the level of the bottle will reset itself
to the maximum volume.
By installing an already open bottle, this will be considered full by the
appliance. It is possible to change the volume by going to the Settings
menu (see point IV.1.B
• to indicate the volume of the full bottle in order to monitor
consumption in real time as well as the volumes served and be
alerted when a bottle needs to be replaced.
4
LABEL NAME NOM RÉFÉRENCE
Select the bottle you want
BOTTLE VOLUME VOLUME BOUTEILLE
to set
Tips:
• If you do not want to replace a bottle and remove the "empty
Select the pictogram on the
right bottle" warning you must replace the bottle with another
label and indicate "0" or " " (nothing) in the volume field.
• By clicking the arrows
wine labels already entered in the appliance. The product
can store up to 5,000 labels in its memory.
.
4
The bottle to be replaced
will flash.
Select the bottle to be
replaced.
Remove the bottle by
pulling it towards you then
downwards.
by bringing it into contact with the bottle, without applying
force.
Tip: To remove a bottle, there is no need to lower the disk to the
bottom. Turn the adjustable bottle support until there is a gap of
one centimetre, then remove the bottle in the normal way.
)
Indicate the name of the
label and the volume of the
bottle that you want to
chateau ...
install in the appliance using
the keyboard on the screen.
75 cl
Then validate .
Repeat the process for the
other bottles.
, it is possible to find all the
Open your new bottle.
Place the bottle neck
inside the bottle connector
socket ensuring that you
insert the plunge tube.
Push the bottle upwards
until compressing the
spring to the maximum,
then tilt the bottle forwards
whilst maintaining it
pushed upwards.
Some bottles may need
securing. To do this, it
is possible to raise the
adjustable bottle support
1 cm
2
1
EN
-15-