Salicru SLC CUBE 3+ PS Mode D'emploi page 82

GENERAL INDEX
1. INTRODUCTION.
1.1. ACKNOWLEDGEMENT LETTER.
2. INFORMATION FOR SAFETY.
2.1. USING THIS MANUAL.
2.1.1. Conventions and used symbols.
3. STANDARD AND QUALITY GUARANTEE.
3.1. DECLARATION OF THE MANAGEMENT.
3.2. STANDARD.
3.2.1. First and second environment.
3.2.1.1. First environment.
3.2.1.2. Second environment.
3.3. UKCA PRODUCT MARK AND UK AUTHORIZED
REPRESENTATIVE.
3.4. ENVIRONMENT.
4. PRESENTATION.
4.1. VIEWS.
4.1.1. Views of the equipment.
4.1.2. Legend corresponding to the equipment views.
4.2. DEFINITION AND STRUCTURE.
4.2.1. Nomenclature.
4.2.2. Structural diagram.
4.3. UPS FUNCTION STAGES.
4.3.1. I/O EMI filters.
4.3.2. Rectifier-PFC stage (AC/DC).
4.3.3. Batteries.
4.3.4. Inverter stage (DC/AC).
4.3.5. Static bypass stage.
4.3.6. Maintenance or manual Bypass.
4.3.7. Terminals for EPO.
4.3.8. Control panel.
4.3.9. Control software and communications.
4.3.9.1. Control software at low level.
4.3.9.2. Managing software of the equipment.
4.3.9.3. Communications.
4.4. OPERATING PRINCIPLE OF AN EQUIPMENT.
4.4.1. Normal operating ().
4.4.2. Mains fault operating ().
4.4.3. Normal operating with Peak Shaving (
4.4.4. Operating with non-active inverter ().
82
4.4.5. Manual bypass operating ().
4.4.6. Frequency converter operating.
4.5. OPERATING STRUCTURE OF A PARALLEL SYSTEM.
5. INSTALLATION.
5.1.
5.1.1.
5.1.2.
5.1.3.
5.1.4.
5.1.4.1.
5.1.4.2. Location for parallel systems.
5.1.4.3. Equipment immobilized and levelled.
5.1.4.4. Preliminary considerations before connecting.
5.1.4.5. Preliminary considerations before connecting, as regards
5.1.4.6. Access to inside the cabinet for its connection.
5.2. CONNECTION.
5.2.1.
5.2.2. Connection of separate static bypass line, terminals (X14 a
5.2.3. Connection to the output, terminals (X6 to X9).
5.2.4. Connection to the battery terminals of the equipment (X11,
5.2.5. Connection to the input main protecting earth terminal (X5)
5.2.6. Relay COM port. Connector (X32).
5.2.7.
5.2.7.1.
5.2.7.2. COM or USB port. Connector (X31
5.2.8. EPO terminals (X50).
5.2.9. Auxiliary contact and battery temperature probe terminal
5.2.9.1. Terminal strip, auxiliary contact of manual bypass switch
5.2.9.2. Terminal strip, auxiliary contact of output switch (X45).
5.2.9.3. Terminal strip, battery temperature probe (X34). For
5.2.9.4. Ethernet connectors (X34
5.2.10. Connection of parallel BUS (X36i) and (X36o).
5.2.10.1. Connection of the communication or BUS bundle (BC).

).
RECEPTION OF THE EQUIPMENT.
Reception, packaging and contents.
Storage.
Transport until its location.
Location, immobilised and considerations.
Location for single equipments.
to batteries and protections.
Connection to mains, terminals (X1 to X4).
X17). CUBE3+ B version only.
X12 and X23), with the battery modules (X47, X48 and X49).
and the earth bonding terminal (X10) .
RS232/RS485 and USB COM 0 ports.
RS232/RS485 COM 0 ports. Connector (X31).
strip.
(X51).
batteries in a separate cabinet only.
) in the UPS and (X38
ETH
the battery cabinet. For separate battery cabinets and
probe bundle > 5 m, only.
).
USB
) in
ETH
SALICRU