Sabo 47-VARIO Livret D'entretien page 46

Filling with fuel
– Only fill the tank with fresh and clean unleaded standard petrol.
Fuel with up to 10% ethanol is acceptable.
– Unscrew tank cap.
– Fill tank with fuel using a funnel up to max. lower edge of filling nozzle.
– Replace tank cap and screw tight.
10 STARTING THE ENGINE
Only start the engine when you are standing behind the mower.
Always place the mower on a level area which is not covered with high grass (if the
grass is too high it will block the cutter bar start-up and make starting the mower
more difficult). When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the cutting tool is
pointing in the direction away from the user, but only as far as absolutely necessary.
As long as the mower has not been lowered to the ground again, both your hands
must be on the top part of the bar.
CAUTION
Hold the starter cable handle firmly when starting. The handle may
otherwise slip out of your hand. Risk of injury!
IMPORTANT
The motor only operates when the safety control bracket is pressed against the
upper part of the handlebar. As soon as the safety control bracket is released,
this returns to its original position under spring force, the motor brake is
actuated, and the motor and blade come to stop within three seconds.
Manual start without electro-start (Illustration D + E )
– Push and hold the safety control bar (1) on the top tube (2) D .
– Slowly pull the starter cable (3) until resistance is felt, then rapidly pull it out E –
the engine begins to run, slowly recoil the cable.
NOTE
This engine has a temperature-controlled automatic choke. The engine runs
with optimum power at maximum speed, which is required for a clean cutting
pattern (engine speed = blade speed).
Electro-start models (Illustration D + P4 + E )
– Push and hold the safety control bar (1) on the top tube (2) D .
– Turn the ignition key (4) clockwise up to the limit stop, for so long until the
engine starts running P4 .
NOTE
To ensure a long service life of the battery and starter, the starting process
should never be longer than 5 seconds.
NOTE
This engine has a temperature-controlled automatic choke. The engine runs with
optimum power at maximum speed, which is required for a clean cutting pattern
(engine speed = blade speed).
NOTE
Should the electric starter be defective at some point, then the engine can also
be started manually.
– Push and hold the safety control bar (1) on the top tube (2) D .
– Slowly pull the starter cable (3) until resistance is felt; then rapidly pull it out E –
the engine begins to run, slowly recoil the cable.
11 SWITCHING OFF THE ENGINE (ILLUSTRATION F + P4 )
– Release the safety control bar (1) F .
– Remove the ignition key (4) (only for electro-start) P4 .
12 EMERGENCY STOPPING
Release the safety control lever and the drive switch bar.
– The mower will stop.
– The blade will stop.
– The engine will stop
Safety instruction!
See table for explanation of symbols page 3
Safety instruction!
See table for explanation of symbols page 3
NOTE
Before every mowing job, make sure that the safety control bar for the engine
brake and the engine drive control bar are working perfectly:
– when the safety control bar is released, the engine and cutter bar must come
to a standstill within three seconds.
– when the engine drive control bar is released, the machine must come to a
standstill immediately.
If this is not the case, please consult your nearest authorised workshop.
13 MOVEMENT DRIVE
Operating the rear wheel drive (only with selective engine drive)
(Illustration G )
The rear wheel drive is switched on and off by means of the drive control handle (1) on the top
guide bar (2) when the motor is running:
– Pull and hold the drive control handle = mower moves
– Release the drive control handle = mower stops (0-position).
The drive control handle must always be pulled firmly up against the top bar. Improper activation
will cause wear on the gearbox. The increased resistance of the bar in the starting position is
deliberate to make accidental operation more difficult.
NOTE
The rear wheels click when the mower is pushed forwards.
Speed adjustment (only for VARIO drive) (Illustration H )
IMPORTANT
The speed may only be adjusted when the engine is running in order to avoid
damage!
The driving speed is set using the rotary knob mounted on the left.
– The knob can be turned in both directions for speed adjustment, so that the required
driving speed can be set. The arrow on the knob indicates the driving speed.
– Position "Hare" = fast (max. speed)
– Position "Tortoise" = slow (min. speed)
NOTE
Mowing at high speed leads to poor cutting pattern or collection result. Always adapt
the speed to the prevailing conditions. For longer grass sections, a slower driving speed
should be selected.
14 GRASS COLLECTOR
Operation with grass collector
WARNING
When operating the equipment with a collecting bag, the bag must be completely
assembled and in technically perfect condition.
IMPORTANT
Make sure that the chute (1) R1 is not bent when handling the collector.
While mowing, ensure that the collector is emptied in good time. The turbo signal on the collector
will indicate when the collector should be emptied.
Turbo signal (shows when the grass collector is full)
(Illustration J + K )
There is an indicator on the top of the collector that shows whether the collector is empty or
full:
– The collector indicator inflates if the collector is empty and during the mowing J .
– If the collector is full, the indicator collapses; once this happens, stop mowing
immediately and empty the collector K .
IMPORTANT
If the fabric of the grass collector is very dirty the turbo indicator will not inflate – in this
case, clean the fabric immediately. The grass collector will only collect grass perfectly if
it is permeable to air.
IMPORTANT
Do not clean the grass collector with hot water!
8
Safety instruction!
See table for explanation of symbols page
3