Panasonic AG-DTL1P Manuel D'utilisation page 59

RS-232C
O Time lapse control commands
Data transmitted by PC
[STX] LAD:m [ETX]
[STX] LAI:m [ETX]
[STX] LAR [ETX]
[STX] LBM:m [ETX]
[STX] LBP:m [ETX]
[STX] LBR:m [ETX]
[STX] LBZ:m [ETX]
[STX] LMS:m [ETX]
[STX] LDA:m [ETX]
[STX] LDF:m [ETX]
[STX] LDM:m [ETX]
[STX] LDO:data1:data2 [ETX]
[STX] LDP:m [ETX]
[STX] LDS:m [ETX]
[STX] LDT:m:n [ETX]
[STX] LDW:m [ETX]
[STX] LDX:m [ETX]
[STX] LFS:nn:mmdd:p [ETX]
[STX] LIP:n:data1:data2:t [ETX]
[STX] LIW:abcdefgh:ijklmnop [ETX]
[STX] LLL:m [ETX]
[STX] LMA:m [ETX]
[STX] LMP:p:n [ETX]
[STX] LNR:f:p:t [ETX]
[STX] LRB:m [ETX]
Data returned from unit in response
[STX] LAD [ETX]
[STX] LAI [ETX]
[STX] LAR [ETX]
[STX] LBM [ETX]
[STX] LBP [ETX]
[STX] LBR [ETX]
[STX] LBZ [ETX]
[STX] LMS [ETX]
[STX] LDA [ETX]
[STX] LDF [ETX]
[STX] LDM [ETX]
[STX] LDO [ETX]
[STX] LDP [ETX]
[STX] LDS [ETX]
[STX] LDT [ETX]
[STX] LDW [ETX]
[STX] LDX [ETX]
[STX] LFS [ETX]
[STX] LIP [ETX]
[STX] LIW [ETX]
[STX] LLL [ETX]
[STX] LMA [ETX]
[STX] LMP [ETX]
[STX] LNR [ETX]
[STX] LRB [ETX]
59
Description of command
Sets the duration of the alarm recording or sensor
recording.
Sets the operation mode that is to be established when an
alarm signal has been input while the tape is at its end
position.
Deletes the ALARM RECALL data.
Sets the processing of the black burst signal when the video
signals are switched.
Prevents the video signals of a specific camera from being
output.
Sets the buzzer when the REW REVIEW results are no-
good.
Sets the buzzer during alarm recording or sensor recording.
Sets the timing at which the video signals which are
supplied from the camera and which are to be output from
the rear panel VIDEO OUT connector are to be switched.
Sets the output of the control signals to the component
connected to the ALARM OUT terminal.
Sets the recording mode in which to perform alarm
recording or sensor recording.
Sets recording mode that is to be established when the
alarm signal has been input.
Sets the start and end times when the control signals are to
be output to the component connected to the EXT TIMER
OUT terminal.
Sets the picture quality for performing alarm recording or
sensor recording.
Selects the mode (field or frame) for performing still-picture
playback.
Sets the recording type in which to record when an alarm
signal has been input to the ALARM IN 1 or 2 terminal.
Sets the output of the control signals which are to be output
to the component connected to the WARNING/REC OUT
connector.
Switches the function of the EXT SW IN/VIDEO OUT
connector.
Sets the free-set timer.
Sets internal timer recording.
Sets the weekly timer and daily timer.
Sets the synchronization system of the cameras to be
connected.
Switches the search mode.
Switches the screen display (4-in-1 or 1-screen display) and
sets the camera numbers.
Sets the recording mode, picture quality and recording type.
Sets the buzzer operation in the event that the unit is kept in
the stop mode for a prolonged period of time.