Note For Ice Maker With Continuous Delivery; Note For Ice Maker With Daily Production Of 21 Kg; Note For Ice Maker With Cold Water Dispenser - Bartscher 104.825A Mode D'emploi

9. drain sanitizing solution remaining in pump body by introducing pressurised water into the suction pipe and checking that the water
exits from the delivery pipe (Fig. 20)
10. thoroughly rinse inner basin, door and container with cold water
11. thoroughly rinse ice-cube slide, evaporator cover panel, sprayer bank and the corresponding side caps, flag support assembly,
overflow pipe, pump filter and sprayer bank feed pipe under running water
12. refit parts previously removed
13. reposition top, securing it to rear panel with the screw, if present
The ice-cube maker can now be reactivated as specified in the instruction manual.
IMPORTANT: All the ice produced during the first five cycles after cleaning and sanitizing operations must be discarded.
THE FOLLOWING ADDITIONAL OPERATIONS ARE REQUIRED FOR SOME SPECIAL MODELS:

11.1 NOTE FOR ICE MAKER WITH CONTINUOUS DELIVERY

To access the inner parts, remove top of appliance (Fig. 18), then remove front upper panel as shown in Fig. 21.
In addition to the operations described in chapters 10 and 11, the following steps must be taken when cleaning and sanitizing the ice
collecting bin (Fig. 21):
1. tilt appliance towards the front by positioning a shim at least 4 cm thick under the back legs
2. position a basin under the ice-cube dispenser pipe (8)
3. raise outlet pipe until it is higher than the appliance
4. pour water and vinegar solution onto ice-cube conveyor screw until solution exits from ice-cube dispenser pipe (8)
5. leave solution in bin for at least 30 minutes, then drain solution and return outlet pipe to its original position
6. wipe ice-cube collection bin walls and conveyor screw with a water and vinegar solution using a sponge and brush; avoid rotations
which could damage the drive motor
7. repeat operations 3 to 6 using the sanitizing solution
8. thoroughly rinse walls of ice collection bin with cold water
9. rinse ice-cube conveyor screw and bottom of bin with cold water, allowing it to flow along the ice dispenser pipe (8)
10. drain water remaining on bottom of bin and return outlet pipe to its original position
11.2 NOTE FOR ICE MAKER WITH ABS FINISHING (Fig. 23)
To access inner basin, evaporator and timer regulation screw:
• remove screw cover
• remove screws with a Phillips screwdriver
• open front door and remove ABS shell

11.3 NOTE FOR ICE MAKER WITH DAILY PRODUCTION OF 21 kg

Perform cleaning and sanitizing operations as described in chapters 10 and 11.
To reach pump filter (Fig. 24):
• remove flag support assembly (1) and ice-cube slide (2) and extract overflow pipe (3) to drain water present in the basin
• disconnect pump connection pipes (10) and sprayer bank (11)
• unscrew the filter threaded ring nut (9)
To access pump side of inner basin:
• remove rear panel by loosening fixing screws and extracting it upwards (Fig. 25)
• remove pump connector pipe (10 in Fig. 24)
• release pump wiring (12 in Fig. 26) and remove pump assembly located on right-hand side of evaporator by lifting it out of its seating,
taking care not to damage the wiring (Fig. 26)
• wipe pump container walls with a water and vinegar solution and sanitizing solution using a sponge; take care not to wet the electrical
parts
• at the end of cleaning and sanitizing operations on the basin, refit pump, taking care to connect sprayer bank connector pipe (10 in Fig.
24) and pump connector pipe (11 in Fig. 24) correctly and to re-secure pump wiring
(12 in Fig. 26)

11.4 NOTE FOR ICE MAKER WITH COLD WATER DISPENSER

Perform cleaning and sanitizing operations as described in chapters 10 and 11, also removing the following components for cleaning and
sanitizing operations (Fig. 27):
• water cooling coil (13)
• coil cover grille (14)
Thoroughly rinse inside of cooling coil by circulating pressurised cold water through it.
Clean and sanitize cold-water dispenser area.
To access timer regulation screw in models with a 21 kg/24h output (Fig. 28):
• remove screw connecting top to rear panel
• raise rear part of top and release it from front hooks
• regulate timer with a flat-head screwdriver