Lubrication - Stiga PRIMO Mode D'emploi

All manuals and user guides at all-guides.com
9. Reinstall the rear wheel and lower the machine.
See 6.3 and 6.4.
10.Start the engine and run at idle for 30 seconds.
11.Check to see if there is any oil leakage.
12.Stop the engine. Wait for 30 seconds and then
check the oil level. See 5.3.
Take the used oil, oily rags etc. to a recycling
station.
6.7 Fuel filter (14:Z)
Replace the fuel each season.
Check that there is no fuel leakage once the new
filter has been installed.
6.8 Deck belt (21:J)
After 5 hours of operation check that the machine's
belts are intact and not damaged.
6.9 Adjusting the drive chain (15:U)
Check/adjust the belt tension each season as fol-
lows:
Check:
1. Raise the machine and remove the right-hand
rear wheel. See 6.4.
2. The chain (15:U) must have 5-10 mm of play.
Any required adjustment, see blow.
Adjustment:
Adjust the play by moving the tensioner wheel as
follows:
1. Slacken off the nut (15:T) and set the tensioner
wheel to the desired position.
2. Tighten the nut and check the play. Adjust again
if required.
3. Tighten the nut to 40-45 Nm when adjustment
has been completed.

6.10 Lubrication

All lubrication points according to the table below
must be lubricated after every 25 operating hours
as well as after each clean.
Item Section below
Drive chain 6.10.1
Steering cable 6.10.2
Tensioning arms 6.10.3
and moving joints
Throttle cable 6.10.4
6.10.1Drive chain
Lubricate the drive chain (15:U) using chain spray
as follows. Use universal type chain spray.
1. Trestle up the machine's right-hand rear wheel
so that it can rotate freely. See 6.3.
2. Brush the chain clean using a wire brush.
3. Rotate the rear wheel by hand and at the same
time spray the chain so that it is fully lubricated.
4. Lower the machine.
ENGLISH
6.10.2Steering cable
See fig. 16. Lubricate the steering cable using
chain spray as below. Use universal type chain
spray.
1. Brush the chain clean using a wire brush.
2. Turn the steering wheel and at the same time
spray the cable so that it is fully lubricated.
6.10.3Tensioning arms moving joints
Lubricate the bearing points using an oil can at the
same time as activating the respective control.
Preferably carried out by two people.
Activate the controls:
• Steering
• Clutch, brake
• Raise the cutting deck
• Engaging the cutting deck.
• Setting the cutting height
6.10.4Throttle cable
See fig. 17. Lubricate the cable ends using an oil
can at the same time as activating the respective
control.
6.11Battery
Never overcharge the battery. Over-
charging can damage the battery.
Do not short-circuit the battery's termi-
nals. Sparks occur which can result in
fire. Do not wear metal jewellery which
can come into contact with the battery
terminals.
In the event of damage to the battery
casing, cover, terminals or interference
to the strip covering the valves, the bat-
tery should be replaced.
The battery is a valve-regulated battery with 12 V
nominal voltage. The battery fluid does not need to
and cannot be checked or topped up. The only
Figure
maintenance that is required is charging, for exam-
15:U ple after extended storage.
16 The battery must be fully charged be-
fore being used for the first time. The
-
battery must always be stored fully
charged. If the battery is stored while
17
discharged, serious damage will occur.
6.11.1 Charging with the engine
The battery can also be charged using the engine's
generator as follows:
1. Install the battery in the machine as shown be-
low.
2. Place the machine outdoors or install an extrac-
tion device for the exhaust fumes.
3. Start the engine according to the instructions in
the user guide.
GB
59