Section Vi - Operational Procedure; Installation Of Usb Flash Drive (Optional); Apply Power; Start-Up Screen - Covidien Genius 2 Manuel D'utilisation

Section VI - Operational Procedure

The following procedure will describe the steps required to operate the Genius™ Checker/Calibrator. In order to facilitate familiarity with the product, it
would be advisable to use this section of the manual during the calibration check of the first few thermometers.

Installation of USB Flash Drive (Optional)

Install a USB flash drive into the USB port located on the front panel if a report file written to the USB flash drive is desired. If the USB flash drive is installed
after performing a calibration check, an error message may occur when attempting to write the report file if the operator does not wait for the USB flash
drive to complete initialization. If the Genius™ Checker/Calibrator is powered off, all internal memory (not yet saved to the USB flash drive) will be lost.

Apply Power

Make sure the AC-adapter end of the power module is plugged into a 100-240VAC outlet. Connect the power module to the front panel power connector.
Apply power to the Genius™ Checker/Calibrator by using the power switch on the front panel.

Start-up Screen

The first screen on the LCD display is the Initialization Screen, which displays the software revision and date of the Genius™ Checker/Calibrator. If there is an
internal problem during initialization, an Error screen will be displayed (See Section VII).

Recalibration Due Screen

An optional screen will appear if the Genius™ Checker/Calibrator is overdue or due very soon for recalibration. The Genius™ Checker/Calibrator is overdue if
it has been more than 1 year since its last calibration, and a reminder will appear if it is due for recalibration within 1 month. This is a reminder to the user
to return the Genius™ Checker/Calibrator to a customer service center for recalibration.

Reminder Screen

The next screen on the LCD display is a reminder to let the Genius™ Checker/Calibrator warm-up for at least 15 minutes after applying power. This will let
the infrared blackbody targets warm up to the proper temperatures. To exit this screen, press the encoder knob.

Ambient Temperature

The next screen on the LCD display has important instructions to use the Genius™ Checker/Calibrator in an environment free from drafts and within the
ambient temperature operating range. To exit this screen, press the encoder knob.

Main Menu

The Main Menu screen is displayed next. This screen has four menu options:
Check Calibration

Preferences

Set User/Site Information
Set Time/Date
To enter any menu option, use the encoder knob to scroll over and highlight the desired menu option, then press the encoder knob.
Preferences
When the Preferences screen is entered, the following choices are available:

Time Format

Date Format

Language
Back
Use the encoder knob to scroll over and highlight the desired menu option, then press the encoder knob.
Time Format
Two time format options are available: 12-hour and 24-hour. The currently selection option has an asterisk "*" character to the left of the option. To select
a time format, highlight the option and press the encoder knob. This selects the highlighted option as the new time format and returns to the Main Menu
screen. Choosing "Back" returns to the Main Menu without changing the format.
Date Format
Three date format options are available: MM/DD/YYYY, DD/MM/YYYY and YYYY/MM/DD. The currently selection option has an asterisk "*" character to the
left of the option. To select a date format, highlight the option and press the encoder knob. This selects the highlighted option as the new date format and
returns to the Main Menu screen. Choosing "Back" returns to the Main Menu without changing the format.

Language Selection

The Language Selection screen lists the available languages for the LCD screen text. To select a language, scroll over the selection and it will be highlighted.
Press the encoder knob to complete the selection and return to the Main Menu screen. The selected language will be stored in non-volatile memory and
will continue to be used next time the unit is powered on.
Genius Checker/Calibrator
TM
5
Table of Contents