Roland OCTAPAD SPD-20 PRO Manuel Du Propriétaire page 24

Connecting External Devices
Trig Type List
Used drum trigger Trig Type
KD-A22
KDA22
KD-200 KD200
KD-140 KD140
KD-120 KD120
KD-85
KD85
KD-10 KD10
KD-9 KD9
KD-8
KD8
KD-7 KD7
KT-10 KT10
KT-9 KT9
PD-128S, PD-128 PD128
PD-125XS, PD-125X PD125X
PD-125 PD125
PD-108 PD108
PD-105X PD105X
PD-105 PD105
PD-85 PD85
PDX-100 PDX100
PDX-12 PDX12
PDX-8
PDX8
PDX-6
PDX6
PD-8 PD8
VH-11 VH11
VH-10 VH10
CY-16RT CY16RT
CY-15R CY15R
CY-14CT CY14CT
CY-14C
CY14C
CY-13R
CY13R
CY-12C CY12C
CY-12R/C CY12R/C
CY-8 CY8
CY-5 CY5
BT1
BT-1
BT1 SENS*1
PAD1
Generic pads PAD2
PAD3
RT-30K RT30K
RT-30HR RT30HR
RT30H SN*2
RT-30H
RT30H TM*3
RT-10K
RT10K
RT-10S
RT10S
RT-10T
RT10T
*1: When using the BT-1, it is possible to further increase the sensitivity
for soft strikes, but this increases the possibility of unwanted
triggering by vibration from the surroundings.
*2: Select this if you attach an RT-30H to the snare.
*3: Select this if you attach an RT-30H to a tom.
24
Rim shot Choke play
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
(
–
(
–
(
–
(
–
(
–
(
–
(
–
(
–
(
–
(
–
(
–
( (
( (
( (
( (
( (
( (
( (
( (
( (
( (
( (
( (
– –
– –
( (
(
–
( (
– –
(
–
– –
– –
– –
(
–
– –
VH SET setting
Here's how to adjust the offset of the hi-hat (VH-10/VH-11).
* This can be set only if TYPE is set to VH-11 or VH-10.
1. With the hi-hat completely separated from the
motion sensor unit, power-on the OCTAPAD.
clutch screw
Separated
motion sensor unit
2. Loosen the clutch screw and let the hi-hat rest
naturally on the motion sensor unit.
3. In the procedure "External Trigger Settings"
(p. 22), select "EXT TRIG" and then press the
[ENTER] button.
4. Strike the hi-hat to select the pad.
5. Set "TYPE" to "VH11" or "VH10."
6. Use the [K][J] buttons to select "VH SET," and then
press the [ENTER] button.
7. If the screen indicates "Turn screw L," turn the offset
adjustment screw counter-clockwise. If the screen
indicates "Turn screw R," turn it clockwise.
offset
adjustment
screw
OPEN
CLOSE
When the value shown on the screen is approximately 80 and the
"OK!" indication appears, the adjustment is complete.
8. Fasten the clutch screw so that the hi-hat opens to
the amount you prefer.