Detergent System (Ecoflex™ Only) - Advance CS7000 Mode D'emploi

A-20 / ENGLISH
DETERGENT SYSTEM PREPARATION AND USE (ECOFLEX MODELS ONLY)
The Detergent Cartridges (47) are located below the Operator's Seat (2). Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of
detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to lling to avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so
you can write the detergent name on each cartridge to avoid mixing them up. When installing a new cartridge, remove the Cap (BC) and place the
cartridge in the detergent box. Install the Dry Break Cap (BD) as shown.
The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over oor drain
before purging because a small amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals (SCRUB AND SOLUTION SYSTEMS MUST BE OFF):
1 Disconnect and remove the detergent cartridge.
2 Turn the key switch (A) to the RUN (ON) position. Wait a few seconds for the start-up sequence to nish.
3 Press and hold the Detergent Switch (X) and the Solution Switch (U) for approximately 2 seconds. Release the switch when the chemical
purge icon (C12) appears on the display and the indicator on the detergent switch (X) starts ashing. NOTE: Once activated the purge
process takes at least 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to
purge the system.
To Purge Weekly (SCRUB AND SOLUTION SYSTEMS MUST BE OFF):
1 Disconnect and remove the detergent cartridge. Install and connect a Cartridge lled with clean warm water.
2 Turn the key switch (A) to the RUN (ON) position. Wait a few seconds for the start-up sequence to nish.
3 Press and hold the Detergent Switch (X) and the Solution Switch (U) for approximately 2 seconds. Release the switch when the chemical
purge icon (C12) appears on the display and the indicator on the detergent switch (X) starts ashing. NOTE: Once activated the purge
process takes at least 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to
purge the system.
When the detergent level is nearing the bottom of the cartridge it is time to re ll or replace the cartridge(s).
SERVICE NOTE: Follow the "To Purge Weekly" instructions above if the machine is going to be stored for an extended period of time or if you
plan to discontinue use of the detergent system.
Detergent Ratio (SCRUB SYSTEM MUST BE ON):
No detergent is dispensed until the scrub and detergent systems are activated and the Drive Pedal (37) pushed forward.
The detergent mixture icon (C1) will always be displayed when the detergent system is on.
There are 4 modes of EcoFlex operation:
1. Minimum Concentration Detergent – Burst of Power Indicator (P1) ON (Activated by momentarily pressing Burst of Power switch when in
maximum concentration detergent mode). See below the steps "To program the Minimum Concentration Detergent Level".
2. Maximum Concentration Detergent – Burst of Power Indicator (P1) OFF (Activated by pressing and holding Burst of Power switch for two
seconds). See below the steps "To program the Maximum Concentration Detergent Level". Do not use a concentration level exceeding the
detergent manufacturer's recommendation.
3. Burst of Power – Press the Burst of Power Switch (P) to increase the detergent ratio for one minute to the pre-programmed "maximum" level
of concentration (as noted in programming instructions below). This will also cause the solution ow rate to increase to the next level and the
scrub pressure to increase to the next level. Burst of Power Indicator (P1) will blink for one minute.
4. Plain Water - During scrubbing, the detergent system can be turned off at any time by pressing the Detergent ON/OFF Switch (X) to
allow scrubbing with water only. Detergent Indicator (X1) will be OFF.
To program the Minimum Concentration detergent level
1. Press the OneTouch™ Scrub switch
2. Ensure the Burst of Power Indicator
3. Press the Detergent ON/OFF Switch
4. Press and hold the detergent switch for approximately 2 seconds until the indicator ashes.
5. While the indicator is ashing, pressing and releasing the detergent switch will cycle through the available ratios (400:1, 300:1, 256:1, 200:1,
150:1, 128:1, 100:1, 64:1, 50:1, 32:1, 26:1).
6. Once the desired ratio is displayed on the screen
7. Whenever the minimum concentration setting is set to a higher concentration than the current maximum programmed concentration setting.
The maximum concentration default setting will be equal to the minimum concentration setting until changed by the operator.
To program the Maximum Concentration detergent level
1. Press the OneTouch™ Scrub switch
2. Press and hold the Burst of Power Switch
mode).
3. Press the Detergent ON/OFF Switch
4. Press and hold the detergent switch for approximately 2 seconds until the indicator ashes.
5. While the indicator is ashing, pressing and releasing the detergent switch will cycle through the available ratios (Note: only ratios that are a
higher concentration or equal to the minimum detergent setting will be available.
6. Once the desired ratio is displayed on the screen
Once set, the detergent ow rate automatically increases and decreases with the solution ow rate, but the detergent ratio remains the same.
A-20 - FORM NO. 56041979 - CS7000
(R) to activate the scrub system.
(P1) is ON (minimum concentration detergent mode).
(X) to turn off the detergent system (detergent indicator (X1) OFF).
(C1), stop and it will save the setting after 3 seconds.
(R) to activate the scrub system.
(P) for approximately 2 seconds until the indicator (P1) is OFF (maximum concentration detergent
(X) to turn off the detergent system (detergent indicator (X1) OFF).
(C1), stop and it will save the setting after 3 seconds.
revised 6/2011