Detergent System; Determine Firmware Main Revision Level Of Your Machine; Firmware Main Revision A Thru D - Advance Condor Mode D'emploi

A-14 / ENGLISH

DETERGENT SYSTEM

DETERMINE FIRMWARE MAIN REVISION LEVEL OF YOUR MACHINE

TO SEE THE FIRMWARE MAIN REVISION:

Press and hold Scrub Off

Release the buttons after the logo has disappeared.

The Display (K) will now show both the "MAIN REVISION" and the "DISPLAY REVISION".

If your Display (K) shows your FIRMWARE MAIN REVISION level is A,B,C,or D, use the old EcoFlex programming instructions.

If your Display (K) shows your FIRMWARE MAIN REVISION level is E or later, use the new EcoFlex programming instructions.

Turn the Key Switch

FIRMWARE MAIN REVISION A THRU D

DETERGENT SYSTEM PREPARATION AND USE (ECOFLEX MODELS ONLY)
COMMON INSTRUCTIONS:
Pressing and releasing the Detergent Switch (J) while the solution system is active will cause the detergent system to alternately turn on and off. The system
should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over fl oor drain before purging because a small
amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals:
1 Disconnect and remove the detergent cartridge.
2 Turn the Key Switch (A) ON. Press and hold the Solution Switch (F) and the Detergent Switch (J) down for 3 seconds. NOTE: Once activated the purge
process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.
To Purge Weekly:
1 Disconnect and remove the detergent cartridge. Install and connect a Cartridge fi lled with clean water.
2 Turn the Key Switch (A) ON. Press and hold Solution Switch (F) and the Detergent Switch (J) down for 3 seconds. NOTE: Once activated the purge
process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.
Detergent Ratio:
1 The detergent ratio is locked at 1:400, except while overriding the EcoFlex cleaning mode. The pre-programmed ratio that is used during EcoFlex override
can be adjusted. With the detergent system OFF, press and hold the Detergent ON/OFF Switch (J) for 2 seconds. The detergent indicator will fl ash and
each press of the switch will cycle through the available ratios (1:32, 1:50, 1:64, 1:100, 1:128, 1:150, 1:200, 1:256, 1:300, 1:400). Once the desired ratio is
displayed on the screen (K9), stop and it will lock in after 5 seconds.
2 With EcoFlex in the OFF/disabled state (LED off) the detergent ratio is adjustable. With the detergent system OFF, press and hold the Detergent ON/OFF
Switch (J) for 2 seconds. The detergent indicator will fl ash and each press of the switch will cycle through the available ratios (see above). Once the desired
ratio is displayed on the screen (K9), stop and it will lock in after 5 seconds.
CARTRIDGE INSTRUCTIONS:
The Detergent Cartridge (29) is located behind the Side Access Panel (27). Fill the detergent cartridge with a maximum of 2.2 gallons (8.32 Liters) of detergent.
SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to fi lling to avoid spilling detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the
detergent name on each cartridge to avoid mixing them up. The system should be purged of previous detergent when switching to a different detergent. When
installing a new cartridge, remove the Cap (AA) and place the cartridge in the detergent box. Install the Dry Break Cap (BB) and detergent hose as shown.
A-14 - FORM NO. 56041986 - Condor™
(E) and Traction Control Switch (B) buttons while turning the Key Switch (A) on.
(A) off to exit revision display mode.
K
E
A
B
revised 9/14