socomec ATyS 6m Notice D'utilisation page 81

Control circuits
Denomination Terminals (1) Description
Power supply Power 101 Source
1
230 V~102
Power supply Power 201 Source
2
230 V~202
Sensing inputs N (103) Neutral
1
source L3 (104) Phase 3
L2 (105) Phase 2
L1 (106) Phase 1
Sensing inputs L1 (203) Phase 1
2
source L2 (204) Phase 2
L3 (205) Phase 3
N (206) Neutral
Commands 207 Commands inputs Common terminal
208 Standby source transfer control input (CTS)
209 Remote test on load input
210 DC power supply for 2I / 2O
Genset 73 Genset start / stop relay - 2 stable positions
start signal (2) 74 Programmable state - factory setting = NO, close to start 5A AC1 / 250 V
Control 313 Control activation
(Impulse / if closed with 317
contactor 314 Position
mode to 315 Position
refer to 316 Position 0 order if closed with 317
programming) 317 Specific voltage supply
Common control terminals 313 to 316
Remote interface RJ ATyS D10 or D20 connection
conection
Position 13 Common I - 0 - II
auxiliary 14 AC position I NO
contacts 24 AC position II NO
34 AC position 0 NO
Auxiliary 43 Auto / manu selector position
contacts 44 Closed in automatic position
/ AUT & 53 Padlocked information
Padlock 54 Closed if padlock is in place
Fault 63 Relay closed when product is faulty
relay 64 (if product is powered)
Second 81 Common AC position I
auxiliary 82 AC position I NC
contact 84 AC position I NO
(option) 91 Common AC position II
92 AC position II NC
94 AC position II NO
Option 0 Connection RS485
Communication -
+
Option I13 + Input
2 Inputs / I14 - Function according to programming
2 Outputs I23 + Input
I24 - Function according to programming
O13 Output Relay
O14 Function according to programming
O23 Output Relay
O24 Function according to programming
Current R1 Current transformer I1
transformer R2
S1 Current transformer I2
S2
T1 Current transformer I3
T2
Voltage and frequency sensing precision: 1 %
(1) Terminal numbers can differ depending on voltage sensing and power supply kit configuration.
(2) Refer to programming, Setup, to modify relay state.
(3) It is recommended to power 2I / 2O modules from terminals 207-210 (refer to connection diagram).
SOCOMEC - Réf. : 532 211 F
1
2
2
order if closed with 317
1
order if closed with 317
Automatic Transfer Switch ATyS
CONNECTIONS
Characteristics
220 to 240 Vac ±20 %
500 Vac (phase-phase)
maximum
288 Vac (phase-neutral)
maximum
500 Vac (phase-phase)
maximum
288 Vac (phase-neutral)
maximum
Do not connect to any
power supply
Dry contact
Do not connect to any
power supply
Maximum distance 3 m
5A AC1 / 250 V
5A AC1 / 250 V
5A AC1 / 250 V
5A AC1 / 250 V
To power from 10 to 30 Vdc (3)
(3)
To power from 10 to 30 Vdc
5A AC1 / 250 V
CT input 5 A
CT input 5 A
CT input 5 A
Recommended
section
1.5 mm 2
1.5 mm 2
1.5 mm 2
1.5 mm 2
4 mm 2
1.5 mm 2
RJ45 8 / 8
1.5 mm 2
1.5 mm 2
2
1.5 mm
2
1.5 mm
1.5 mm 2
2
1.5 mm
2
1.5 mm
2
1,5 mm
1,5 mm 2
1,5 mm 2
81