Important Information; Description; Before First Use; Care Of The Battery - Carrera DIGITAL 124 Instructions De Montage Et D'utilisation

Important Information

EXCLUSIV Carrera DIGITAL 124
Carrera DIGITAL 124
Please note that Exclusiv (analog system) and Carrera DIGITAL
124/132 (digital system) involve two separate and completely inde-
pendent systems. We hereby expressly indicate that both systems
must be kept separate when setting up the track, i.e. no connecting
rail from Exclusiv may be used together with the connecting rail and
Control Unit of the Carrera DIGITAL 124/132, even if only one of the
two connecting rails (Exclusiv connecting rail or Carrera DIGITAL
124/132 connecting rail and Control Unit) is attached to the current
supply. Furthermore, no other Carrera DIGITAL 124/132 compo-
nents (switches, electronic lap counter, pit stop) may be built into an
Exclusiv course, i.e. via analog operation.
Non-compliance with the above information may result in damage or
destruction of the respective Carrera DIGITAL 124/132 components.
In this case no warranty may be claimed.

Description

WIRELESS+ is the latest new cordless racetrack delight for Car-
rera DIGITAL124 and Carrera DIGITAL 132. The 2.4 GHz radio
technology with frequency-hopping is free of interference and offers
a range of up to 15 metres. Thanks to powerful lithium polymer re-
chargeable battery, continuous play for up to eight hours is possible
and stand-by operation for over 80 days. WIRELESS+ in conjunc-
tion with DIGITAL 124 offers wireless freedom for up to four drivers
on the racetrack.

Before first use

Before first using the speed controller, the rechargeable battery
supplied must be inserted in the controller. Unscrew the battery
2
compartment on the underside of the speed controller.
1
Connect the battery plug into the socket in the speed controller and
put the battery in place in the compartment. Finally screw down the
cover of the battery compartment again. The battery is part-loaded
at the factory, but it should be charged completely before being
used for the first time.
1
12

Care of the battery

To make sure the battery performs well for as long as possible, the
following points should be observed regarding its care and storage.
• Before first using them, new batteries should always be charged
fully.
• With a fully-charged battery, continuous play is possible for up
to eight hours. When the battery power is falling off, range of the
speed controller will diminish. As soon as you notice this, the battery
should be fully recharged.
• If it is not to be used for an extended period, remove the battery
and store the controller at room temperature (16-18 °C) in a dry
place. To prevent a deep discharge of the battery, the stored battery
should be charged every 2 to 3 months.

Assembly instructions

EXCLUSIV
1
2
+ +
Before assembling please insert the connecting clips
1 2 3
in the track as shown in figure
base. Move the connecting clips according to figure
of the arrow until they audibly snap in. The connecting clip may also
be inserted later. The connecting clips can be removed into both
directions by simply pressing down the clamped nose (see fig.
Fastening: To fasten the track sections on a board, it is nec-
4
essary to use the track section fasteners (Item no. 20085209, not
contained in the package).
Note:
Carpeting is not a suitable foundation on which to build the track be-
cause of static charging, formation of fluff and ready inflammability.
The Position Tower
necting section F
tioned at any place within the racetrack.

Guard Rails and Supports

1
3
2
1
Guard rails: Guard rail mounts are fitted by tilting them upwards
1
onto the verge of the track.
+
Supporting raised sections: The shank of the ball pivot is
2 3
to be inserted into the square slots provided on the underside of the
track. The supports can be made higher by using the extensions.
The pedestal of the supports can be screwed to a base if required
(screws not included).
Supporting steep curves:
4
4
3
. Stick tracks together on a flat
1
in direction
2
is suitably connected to the shoulder con-
or to the Adapter Unit ; the latter can be posi-
2
4
Slanting supports of the right height are provided to support steep
curves. Fix the nonadjustable supports at the beginning and end of
the curves. Insert the heads of the supports in the round slots of the
underside of the track.

Electrical connection

1
1 Connect the transformer plug with the Control Unit.
Note: To avoid short-circuits and electrocution, the toy may not be
connected using foreign devices, plugs, cables or other objects for-
eign to this toy. The Carrera DIGITAL 124 car racetrack only works
properly with an original Carrera DIGITAL 124 transformer.
The PC interface (PC Unit) may only be operated together with the
original Carrera PC Unit.

Car components

1
).
3
14
3
15
7
6
8
3
9
12
13
Body
1
Engine block
2
3 Tyres
Rear axle
4
5 Rear axle receptacle
including spacer plate
Front axle
6
Front axle mounting
7
Board
8
Central magnet
9
Rear magnet
10
Chassis
11
Rocker arm including spring
12
Guide keel with double sliding contact
13
Center magnet retainer
14
15 Fastening plate
Note: vehicle construction depends on the model.
The designation of the individual parts may not be used as
order numbers.
11
2
3
4
5
3
10
11