Shared Flue Gas System; Air Supply (=Mm Air) - Nordpeis Salzburg C Manuel D'installation

is not in good working order. The draught is mainly
controlled by gas temperature, outside temperature, air
supply as well as the height and inner diameter of the
chimney. The diameter of the chimney should never
be less than that of the flue/chimney collar. At nominal
effect there should be a negative pressure of 12 to 25
Pascal.
The draft increases when:
• The chimney becomes warmer than the outside air
• The active length of the chimney over the hearth
increases
• Good air supply to the combustion
It can be difficult to obtain the right draught conditions
in case the chimney is too large relative to the fireplace,
as the chimney does not heat up well enough. In
such cases you may want to contact professional for
evaluation of possible measures. Draught that is too
strong can be controlled with a damper. If necessary,
contact a chimney sweeper. The product is type
tested and should be connected to a chimney that is
dimensioned for the smoke gas temperature indicated
in the CE declaration. When necessary, contact a
professional in advance
Attention! It is recommended to use a qualified
professional when installing a new fireplace.

Shared flue gas system

Appliance can be connected to shared flue gas pipe
sytem.
Warning! In case of the appliance connected to
shared flue gas pipe system - the Self Closing
Door system must be operational. See FIG 62

Air supply (=mm AIR)

A set for fresh air supply is available as an accessory.
This will ensure that the air supply to the combustion
chamber is less affected by ventilation systems, kitchen
fans and other factors which can create a down-draught
in the room. In all new constructions, we strongly
recommend the product is designed and prepared
for direct supply of outside air. In older houses also,
the use of fresh air supply set is also recommended.
Insufficient air supply can cause poor draught and
thereby low combustion efficiency and the problems this
entails: soot stains on the glass, inefficient utilisation of
the wood and a soot deposits in the chimney.
Warning! Keep the air intakes, supplying
combustion air, free from blockage.
Warrning! Extractor fans when operating
in the same room or space as the appliance
may cause problem.
Distance illustration (FIG 1)
*The illustration indicates the approximate centre height
24
of the recess for the flue. Consider possible inclination
of the flue prior to making perforating the chimney.
Distortions in floors and walls may also influence the
height, dry stack therefore the fireplace for accurate
height and positioning of the flue/chimney connection. If
a fresh air supply set (accessory) is connected through
the floor, mark where the hole should be.
Attention! Since the inner core is composed of
many layers the connection height may vary by up
to a few centimeters from installation to installation.
Safety distances (FIG 2)
Ensure that the safety distances are complied with.
IMPORTANT! Drying Process
The fireplace contains a lot of moisture when it is
new and no fire has been made before. This mois-
ture must be dried out before the fireplace can with-
stand the combustion rate given below.
To extract the moisture, follow this procedure:
1. Ensure that the air vent control just below the door is
completely open
2. Ensure that the bypass and flue dampers are both
open
3. Make a small fire with 0.5-1 kg of kindling wood
4. Close the bypass damper once the flames have
taken proper hold of the wood, this will ensure that
the hot smoke circulates the ducts.
NB! Let the air vent and flue damper remain open
until the fire is burnt out.
This procedure is repeated twice more, with a 24 hrs
gap between each time.
NB! Failure to follow the guidelines for drying can
cause the elements to crack.
The air vent control is turned to the right to increase
the air supply to Salzburg. The vent is working in
two modes.
A. When you turn the vent maximally to the right it is in
ignition mode.
B. If you turn the vent to the left ingnition air is diminish.
When you felt a click then ignition air is closed and there
is maximum secondary air provided. Futher turning to
the left decraese amount of secondary air.
-
GB
B
+
A