Adjustment Of Legs; Flue Outlet Collar; Rear Connection; Connecting The Flue - Nordpeis Uno 1 Manuel D'installation

Masquer les pouces Voir aussi pour Uno 1:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Disassembling / Assembling Thermotte FIG 11-20
Dissasembling the Thermotte
FIG 12. Carefully pull the lower end of the back plate
diagonally towards the door. Leave it at an angle as
shown in the illustration.
FIG 13. Remove the smoke baffle by moving it carefully
to one side and clear of the rail on the other side. Place
the smoke baffle at an angle and carefully remove it
through the door.
FIG 14. Remove the back plate by tilting it carefully
through the door.
FIG 15. Lift the bottom plate up on one side and the the
other.
Assembling the Thermotte
FIG 16. Carefully tilt the bottom plate through the door
opening. Carefully lower it down on one side before
lowering it on the other.
FIG 17.Tilt the back plate through the door and place it
at an angle (bottom part towards the door) . Leave the
back plate at this angle FIG 18.
FIG 19. Carefully tilt the smoke baffle through the door
and place it eavenly above the upper rails, one side at
the time. Make sure the smoke baffle is centered FIG
19C.
FIG 20. When the smoke baffle is in place, carefully
push the bottom of the back plate in place.

Adjustment of legs

Uno 1/2: Do not have adjustable legs
Uno 4
Open the door under the combustion chamber FIG 3.
Remove the fitting covering the leg adjustment and
adjust the legs with a 17 mm wrench.
In addition, Uno 4 has optional legs sold separately.
See manual Uno Legs for details.
Attention! Adjusting the legs affects both the
top and rear connection height.

Flue outlet collar

Uno is delivered standard with a top flue outlet
collar.
Rear connection FIG 4-10
Remove the top plate and use a 5mm Allen key to
release and remove the smoke collar FIG 4.
Loosen the screws holding the brackets for the
back plate FIG 5.
Carefully pull the brackets upwards FIG 6A and pull the
back plate backwards and off FIG 6B.
Remove the cut out in the back plate FIG 7.
Remove the rear smoke outlet cover FIG 8, and place
it over the top outlet FIG 9A. Move the smoke collar on
the back of the product and fasten it FIG 9B.
Put the back plate back in place and tighten the screws
holding it in place FIG 10
Adjusting the door under the combustion chamber,
Uno 4
The hinges can be adjusted according to FIG 21

Connecting the flue

Please be aware when connecting the 150 mm flue to
the smoke dome that the flue is placed outside the flue
outlet collar. *Alternative versions exsist due to
National requirements. For the flue connection to the
chimney, follow the recommendations from the chimney
manufacturer
Air supply
For connecting the fresh air supply set see FIG Uno Air
1, 2 and 4/5.
Placement of CE mark
The CE-mark which is included should be placed on the
stove.
Uno 1: The CE mark should be placed on the
back of the pedestal.
Uno 2: The CE badge should be placed on the
inside of the panel under the door.
Uno 4:
The CE badge should be placed to the right
in the compartment under the door.
Removing the self closing mechanism FIG 22
The self closing door mechanism connected to the
stove at the bottom left corner. Carefully unhook the
spring and remove the small screw holding the arm
connected to the door. The self closing mechanism is
now deactivated.
GB
.
11

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Uno 2Uno 4

Table des Matières