Alimak Tractel Rollclamp Manuel D'installation, D'emploi Et D'entretien page 14

rollbeam (fig. 5.2, item 1)
1. Positioning the anchor bar center (fig. 1.2, item 8)
on the same center as the adjustable flanges thread
EN
hole as shown (fig. 5.2).
2. Turn the anchor bar clockwise to screw it inside
adjustable flanges (fig. 1.2, item 3) thread hole.
3. Introduce clamping pads (fig. 1.2, item 4) inside
adjustable flanges side thread hole.
4. Hand screw the locking screws (fig. 1.2, item 5)
inside adjustable flanges side thread hole.
corso (fig. 5.3, item 1)
Turn the adjustable rod (fig. 1.3, item 5) by turning
the adjustable hand lever (fig. 1.3, item 4) in
anticlockwise turn.
8.3.2. Installing the anchor device
rollclamp (fig. 6.1)
1. Place the fixed jaw (fig. 1.1, item 6) on the first side
of the beam.
2. Unlock the indexing knob (fig. 1.1, item 4) by
positioning the notch as shown.
3. Release the mobile jaw (fig. 1.1, item 3) by pulling
on the indexing knob (fig. 1.1, item 4).
4. Slide the mobile jaw (fig. 1.1, item 3) while holding
the indexing knob (fig. 1.1, item 4).
5. Place the mobile jaw (fig. 1.1, item 3) on the other
side of the beam.
6. Lock the mobile jaw (fig. 1.1, item 3) on the guide
rod (fig. 1.1, item 7) by releasing the indexing knob
(fig. 1.1, item 4).
7. Lock the indexing knob (fig. 1.1, item 4) by
positioning the notch opposite the locking pin
(fig. 1.1, item 5) as shown.
Check that the indexing knob pin (fig. 1.1, item 4)
is properly engaged in an indexing hole (fig. 1.1,
item 9) of the guide rod (fig. 1.1, item 7).
Check that the total clearance between the guide
shoes (fig. 1, item 2) and the beam is less than
14
DANGER
IMPORTANT
10 mm.
IMPORTANT
Check that the securing strap is not placed
between the beam and the guide rod (fig. 1,
item 7).
rollbeam (fig. 6.2)
1. Place the first adjustable flange guide rollers
(fig. 1.2, item 1) on the first side of the beam.
2. Hand turn the anchor bar (fig. 1.2, item 8) clockwise
to place the second adjustable flange guide rollers
(fig. 1.2, item 1) on the second side of the beam.
3. Attach the adjustment handle (fig. 1.2, item 14) at
the end of the anchor bar (fig. 1.2, item 8) on the
side with the double drill hole.
4. Turn the adjustment handle until the distance
between the guide rollers (fig. 1.2, item 1) and the
beam side is adjusted to match 4mm maximum
clearance (fig. 6.2)
5. When the adjustment has been correctly made,
the oval part of the securing anchor point (fig. 1.2,
item 13) must be turned to point downwards
6. Hand tighten the two locking crews (fig. 1.2, item 5)
on the anchor bar (fig. 1.2, item 8) with the screw
tool (fig. 1.2, item 14)
7. Remove the adjustment handle.
IMPORTANT
Check that the total clearance between the flange
guide rollers (fig. 1.2, item 1) and the beam is less
than 4 mm.
corso (fig. 1.3)
1. Place the first flange hook (fig. 1.3, item 1) on the
first side of the beam.
2. Turn the adjustable hand lever (fig. 1.3, item 4)
clockwise to place the second flange hook (fig. 1.3,
item 1) on the second side of the beam.
3. When the flange hooks are just in contact with
beam sides, the oval part of the securing anchor
point (fig. 1.3, item 13) must be turned to point
downwards
4. Hand tighten the adjustable hand lever (fig. 1.3,
item 4) to lock the anchor device on the beam.