Cub Cadet Pro Z Serie Manuel De L'utilisateur page 16

2. Move the ROPS into the desired position. The three positions are TRANSPORT
position, TRANSPORT WITH BAGGER position and OPERATION position (Figure 23
on page 15).
3. Rotate both locking pins into the LOCKED position. Move the upper ROPS slightly
until the locking pins are fully engaged in the LOCKED position.
Y. FUEL GAUGE(S) (IF EQUIPPED)
There is a fuel gauge on top of each of the two
fuel tanks or a single gauge to the right of the
operator's seat on the RH console. The gauges
measure the fuel level in each tank.
Z. FUEL VALVES
1. Dual Valve Models (if equipped) - The fuel valves
are located near the rear of each fuel tank. The valves
control the fuel flow from the right and left tank and
also can shut off fuel flow to the engine. Rotate the valve
counterclockwise to open the flow from the tank(s). Rotate
the valve clockwise to stop the flow from the tank(s). The fuel tanks can be
operated together, independently or shut the fuel flow off completely.
NOTE: If both tanks are on, and one is empty, the engine will not start. Be certain
to make sure both tanks have fuel or that the empty tank's fuel valve is closed.
2. Single Valve Models
(if equipped) - The fuel
valve is located on the right side of the mower, between the right fuel tank
and engine. The valve controls the fuel flow from the right and left tank and
can also shut off fuel flow to the engine. Rotate the valve clockwise to open
the flow from the right tank (valve pointing at right tank). Rotate the valve
counterclockwise to open the flow from the left tank (valve pointing at left
tank). Rotate the valve halfway (valve pointing at operator's seat) to shut fuel
flow off completely.
NOTE: If fuel flow is shut off, the engine will not start.
AA. ACCESSORY SWITCH RECEPTACLES
The two receptacles for optional accessories are on the RH console. See the
Replacement Parts and Accessories section for information.
AB. 12V OUTLET (IF EQUIPPED)
The 12V outlet is located to the right of the operator's seat on the lower panel of the
RH console and is used for the convenience of plugging in accessories that require a
power source with a maximum load of 5A at 12V.
BEFORE OPERATING YOUR MOWER
1. Before you operate the mower, study this manual carefully to familiarize yourself
with the operation of all the instruments and controls. It has been prepared to
help you operate and maintain your machine efficiently.
2. Fill the fuel tank with only clean, fresh, unleaded gasoline with a pump sticker
octane rating of 87 or higher. When the fuel reaches 1/2" below the bottom of
the fill neck, stop. DO NOT OVERFILL. Space must be left for expansion.
3. Never use gasoline containing more than 10% ethanol or methanol.
4. Check the engine oil level as instructed in the Engine Operator's Manual.
OPERATION
5. Check the transmission oil level.
a. Parker Transmission (if equipped) - The transmission oil expansion
reservoir is located beneath the operator's seat. Always wipe off the area
around the reservoir fill neck before checking the oil level to prevent dirt
from contaminating the oil. Remove the cap and make sure the oil level is
1/4" above the bottom of the reservoir. If the oil level is low, fill with Castrol™
(Syntec®) Edge™.
b. Hydro-Gear Transmission (if equipped) - The transmission oil expansion
reservoirs are located behind the operator's seat, to the right and left of the
engine. Always wipe off the area around the reservoir fill neck before checking
the oil level to prevent dirt from contaminating the oil. Remove the cap and
make sure the oil level is at the "FULL COLD" line. If the oil level is low, fill with
20W50 oil.
6. Check the tire inflation pressures. 10-12 psi for the rear tires, 20-25 psi for the
front tires.
NOTE: New tires are over-inflated in order to properly seat the bead to the rim.
7. Check that all nuts, bolts and screws are tight.
8. Check the tension of the deck drive belts.
a. Remove the deck cover.
b. The tension of the deck drive belts are maintained by a spring mechanism that
adjusts for wear and stretch.
c. Examine the belts for cuts, fraying and excessive wear. Replace if any of these
are detected.
d. Replace the deck cover.
9. Check if deck is level. When correctly adjusted the mower deck should be level
side to side, and the front of the deck should be approximately 1/4" lower than
the rear of the deck. If deck needs to be leveled, refer to the Product Care section.
10. Lubricate all pivot points listed in the Product Care section.
11. Adjust the seat for operator's maximum comfort, visibility and for maintaining
complete control of the machine. Refer to the Set-up section for instructions on
adjusting the seat.
SAFETY INTERLOCK SYSTEM
This machine is equipped with a safety interlock system for the protection of the
operator. If the interlock system should ever malfunction, do not operate the
machine. Contact your authorized service dealer.
• The safety interlock system prevents the engine from cranking or starting unless
the speed control pedals are in the neutral position, the parking brake is engaged
and the PTO knob is disengaged.
• To avoid sudden movement when disengaging the parking brake, the safety
interlock system will shut off the engine if the speed control pedals are moved to
a position other than the neutral position when the parking brake is engaged.
• The safety interlock system will shut off the engine if the operator leaves the seat
before engaging the parking brake.
• The safety interlock system will shut off the engine if the operator leaves the seat
with the PTO knob engaged, regardless of whether the parking brake is engaged.
NOTE: The PTO knob must be in the disengaged position to restart the engine.
16