Cub Cadet Pro Z Serie Manuel De L'utilisateur page 14

E. THROTTLE
Manual Throttle (if equipped)
The throttle control is located on the RH console to the right of the
operator's seat. When set in a given position, a uniform engine speed will
be maintained. The throttle control moves between the FAST
SLOW positions.
Push the throttle control handle forward to increase the engine speed. The
mower is designed to operate with the throttle control in the FAST
throttle) position when the mower is being driven and the mower deck
is engaged.
Pull the throttle control handle rearward to decrease the engine speed.
Electronic Throttle (E-Governor) Lever (if equipped)
The electronic throttle (E-governor) lever is used to control engine speed
and RPM's. It also helps control fuel efficiency. The electronic throttle
lever moves between the FAST
position is used for basic transportation of the mower with the
PTO disengaged and uses the least fuel. The FAST
used when the PTO is engaged and uses the most fuel. The mower should
be started in the START position, but should always be in the FAST
position when the PTO/deck is being used.
F. CHOKE KNOB (IF EQUIPPED)/MIL (IF EQUIPPED)
Choke Knob (if equipped) - The choke knob is located on the
left side of the mower next to the operator's seat. Pull the knob
out to choke the engine; push the knob in/down to open the choke.
Having the choke in the ON position helps the engine to start
during initial start-up. During normal operation the choke should
be OFF.
MIL (if equipped) - The Multifunction Indicator Light (MIL) provides diagnostic
information for the engine. If the MIL lights up and/or flashes see the service manual
or contact your service center.
G. PARKING BRAKE LEVER
The parking brake lever is located to the left of the operator's seat. When
pulled up it engages the parking brake and when pushed down it releases
the brake.
NOTE: If the forward or reverse drive pedal is engaged when engaging the
parking brake, the engine will stop. The parking brake must be placed in the
engaged position when starting the engine.
H. FORWARD DRIVE PEDAL
The forward drive pedal is located on the right side of the machine, directly
to the right of the steering column. Press the forward drive pedal
forward to cause the mower to travel forward. Ground speed is also
controlled with the forward drive pedal. The further forward the
pedal is pivoted, the faster the mower will travel. The pedal will
return to its original/neutral position when it is not pressed.
and
and SLOW positions. The SLOW
position should be
OPERATION
I. REVERSE DRIVE PEDAL
The reverse drive pedal is located on the right side of the mower,
to the right of the forward drive pedal, along the running board.
Ground speed is also controlled with the reverse drive pedal. The
further downward the pedal is pivoted, the faster the mower will
travel. The pedal will return to its original/neutral position when it is
not pressed.
(full
J. FUEL TANK CAPS
The fuel tank caps are located on the top of the fuel tank on the left and right side
of the seat. Turn the fill cap counterclockwise to remove and clockwise until it clicks
three times to tighten. Always re-install the fuel cap tightly onto the fuel tank
after removing.
Never fill the fuel tank when the engine is running. If the engine is hot from
recently running, allow to cool for several minutes before refueling. Highly
flammable gasoline could splash onto the engine and cause a fire.
K. SEAT ADJUSTMENT ROD (NOT SHOWN)
The seat adjustment rod is located below the front/right of the seat. The rod allows
for adjustment forward or rearward of the operator's seat. Refer to the Set-up section
for instructions on adjusting the seat position.
L. SEAT TILT KNOB (NOT SHOWN)
The seat tilt knob is located on the left side of the seat. Refer to the Set-up section for
instructions on adjusting the seat tilt.
M. ARM REST HEIGHT KNOBS (NOT SHOWN, IF EQUIPPED)
The arm rest height knobs are located under the seat arms and can be used to adjust
the height of the arm rests. Refer to the Set-up section for instructions on adjusting
the arm rest position.
N. MECHANICAL SUSPENSION MECHANISM/AIR RIDE (NOT
SHOWN, IF EQUIPPED)
The mechanical suspension mechanism is located on the front of the seat and can
adjust the weight/ride adjustment for operators in the 125- to 275-pound weight
range. Refer to the Set-up section for instructions on adjusting the mechanical
suspension mechanism.
O. LUMBAR SUPPORT LEVER (NOT SHOWN, IF EQUIPPED)
The lumbar support lever is located on the right side of the seat on the seat back.
Refer to the Set-up section for instructions on adjusting the lumbar support.
P. SEAT PROP (NOT SHOWN)
The seat prop is located on the left, rear side of the operator's seat. It is used to prop
the seat forward.
Q. SEAT LATCH (NOT SHOWN)
The seat latch is located below the rear, center of the operator's seat. The latch is used
to secure the seat into the operating position. Lift the latch and tilt the seat forward
to access the area under the seat.
14
WARNING