Cub Cadet Pro Z Serie Manuel De L'utilisateur page 25

4. Route the free end of the oil drain hose toward an appropriate oil collection
container with at least a 2.5 quart capacity, to collect the used oil.
NOTE: Avoid getting oil on the muffler when draining.
5. While holding the free end of the oil drain hose over the oil collection container,
unscrew the square-head hose plug from the end of the hose (Figure 32 on page
24). Drain the engine oil into the collection container.
6. Remove the oil filter to make sure all the oil is drained.
7. After draining the oil, wipe any residual oil from the oil drain hose. Thread the
square head plug into the drain hose fitting and fully tighten the plug.
8. Replace the oil filter and refill the engine with new oil as instructed in the
Engine Operator's Manual. Refer to the Engine Operator's Manual for information
regarding the volume and weight of engine oil.
9. Place the hose back into the clip securing it to the frame.
Lubrication
Periodically lubricate all pivot points with a quality lubricating oil.
Tires
Check the tire air pressure after every 50 hours of operation or weekly. Keep the
tires inflated to the recommended pressures. Improper inflation will shorten the
tire service life and produce an uneven cut. See the tire side wall for proper inflation
pressures. Observe the following guidelines:
• Do not inflate a tire above the maximum pressure shown on the sidewall of
the tire.
• Do not reinflate a tire that has been run flat or seriously under-inflated. Have it
inspected and serviced by a qualified tire mechanic.
Battery Information
Should battery acid accidentally splatter into the eyes or onto the skin,
rinse the affected area immediately with clean cold water. Seek prompt
medical attention.
If acid spills on clothing, first dilute it with clean water, then neutralize with
a solution of ammonia/water or baking soda/water.
NEVER connect (or disconnect) battery charger clips to the battery while the
charger is turned on, as it can cause sparks.
Keep all sources of ignition (cigarettes, matches, lighters) away from the
battery. The gas generated during charging can be combustible.
As a further precaution, only charge the battery in a well ventilated area.
Always shield eyes and protect skin and clothing when working
near batteries.
Batteries contain sulfuric acid and may emit explosive gases. Use extreme
caution when handling batteries. Keep batteries out of the reach
of children.
The battery may present a risk of fire or chemical burn if misused. Do not
open, disassemble, overheat, or incinerate the battery.
BATTERY MAINTENANCE
• Some batteries are filled with battery acid and then sealed at the factory.
However, even a "maintenance free" battery requires some maintenance to
ensure its proper life cycle.
PRODUCT CARE
WARNING
• Spray the terminals and exposed wire with a battery terminal sealer, or
coat the terminals with a thin coat of grease or petroleum jelly, to protect
against corrosion.
• Always keep the battery cables and terminals clean and free of corrosion.
• Some models are equipped with a battery containing a liquid electrolyte. Handle
the battery with care and avoid tipping to prevent leakage.
Batteries contain sulfuric acid and may emit explosive gases. Use extreme
caution when handling batteries. Keep batteries out of the reach
of children.
BATTERY STORAGE
1. When storing the mower for extended periods, disconnect the negative battery
cable. It is not necessary to remove the battery.
2. All batteries discharge during storage. Keep the exterior of the battery clean,
especially the top. A dirty battery will discharge more rapidly.
3. The battery must be stored with a full charge. A discharged battery can freeze
sooner than a charged battery. A fully charged battery will store longer in cold
temperatures than hot.
4. Recharge the battery before returning to service. Although the mower may start,
the engine charging system may not fully recharge the battery.
REMOVING THE BATTERY
1. Flip the seat all the way forward.
2. Remove the bolt and nut securing the negative cable grouping (b) to the negative
battery post (marked NEG (-)). Move the cable grouping away from the negative
battery post (Figure 33).
a
3. Remove the bolt and nut securing the positive cable grouping (c) to the positive
battery post (marked POS (+)) (Figure 33).
4. Unhook the strap (a) holding the battery in place (Figure 33).
5. Carefully lift the battery out of the mower.
6. Install the battery by repeating the above steps in the reverse order.
NOTE: Place the thickest cable closest to the battery terminal.
NOTE: Wiring harness should lay on top of battery hold down strap, otherwise
damage to the wiring harness may result (Figure 33).
25
WARNING
b
c
Figure 33