Publicité
Les langues disponibles
Les langues disponibles
r_
MULTI ZONE
MULTI ZONE MUSIC ENTERTAINMENT
SYSTEM
• When the outputs of the "ZONE2"
OUT terminals
are wired and connected
to integrated
amplifiers installed in other rooms, different sources
can be played in rooms other than the main zone in which this unit and the playback devices are installed. (Refer to ZONE2 on the diagram
below.)
• ZONE 2 SPEAKER OUT can be used when "ZONE2"
is selected at System Setup Menu "Power
Amp Assignment".
In this case, Surround
Back Speaker Out cannot be used for MAIN ZONE.
• When a sold separately room-to-room
remote control unit (DENON RC-616, 617 or 618)is
wired and connected
between
the main zone and
zone2, the remote-controllable
devices in the main zone can be controlled from zone2 using the remote control unit.
NOTES:
• For the AUDIO outputs,
use high quality pin-plug cords and wire in such a way that there is no humming or noise.
• For instructions
on installation and operation of separately sold devices, refer to the devices' operating instructions.
• When the main unit is set to the recording output mode, zone2 remote control key cannot be operated.
POWER AMP ASSIGNMENT
setting ..... Set this to switch the surround back channel's power amplifier for use for the ZONE2. (See page 28)
SURROUND
BACK button ..................... Operate the surround back button to switch surround back channel ON/OFR (main unit and remote
control unit)
ZONE2 ON/OFF
button
..........................
Operate the ZONE2 button to switch ZONE2 line out and speaker out ON/OFR(remote
control unit)
•
MULTI
ZONE
MUSIC
ENTERTAINMENT
SYSTEM
(When
using
LINE OUT)
"POWER AMP ASSIGNMENT"
setting is S. BACK mode.
• 6.1-channel
playback using the surround back speaker is possible in the MAIN ZONE.
• To use the surround back speaker, turn on the SURROUND
BACK button.
• To use the ZONE2 line output, turn on the ZONE2 button.
• The ZONE2 OUT terminal's output level cannot be adjusted with the remote control unit.
ZONE2
RC-617
4
INTEGRATED
AMPLIFIER
,"_"
REMOTE
I_
CONTROL
UNIT
wkh ZONE2
mode
: AUDIO signal cable
RC-616
MAIN ZONE
AVR-1804/884
D
Fd-1 B
[_
_,°;°
_
REMOTE
CONTROL
UNIT
D
B
B
--
: SPEAKER cable
>24
Power
Amp Assignment
I_I_E_r_)ZONE2
SURROUND
BACK
SURROUND
OFF ZONE2
ON
BACK
(Main unit's front panel)
(Remote
control unk)
•
MULTI
ZONE
MUSIC
ENTERTAINMENT
SYSTEM
(When
using SPEAKER
OUT)
"POWER AMP ASSIGNMENT"
setting is ZONE2 mode.
• The SPEAKER OUT and LINE OUT terminals
can be used simultaneously
in ZONE2.
• To use the ZONE2 line output and speaker output, turn on the ZONE2 button.
• The output of the ZONE2 SPEAKER OUT terminals can be adjusted with the remote control unit's ZONE2 VOLUME
+ and - keys.
• The SURROUND
BACK button on the front panel cannot be used.
ZONE2
J
sS4'_S, S
REMOTE
IO
CONTROL
UNIT
wkh ZONE2
mode
: SPEAKER cable
MAIN ZONE
AVR-1804/884
D
D
B
r_
,,o,,,
i_
REMOTE
CONTROL
UNIT
D
B
RC-616
>24
Power
Amp Assignment
& BACK_F_*T_IF;I
OFF ZONE2
ON
_(Light)
(Main unk's front panel)
(Remote
control unit)
41
Publicité
