Publicité
Les langues disponibles
Les langues disponibles
r_
CONNECTIONS
• Do not plug in the AC cord
until all connections
have been
completed.
• Be sure to connect the left and right channels properly (left with
left, right with right).
• Insert the plugs securely. Incomplete connections
will result in the
generation of noise.
• Use the AC OUTLETS for audio equipment
only. Do not use
them for hair driers, etc.
• Note that binding pin plug cords together with AC cords or placing
them near a power transformer
will result in generating
hum or
other noise.
• Noise or humming
may
be generated
if a connected
audio
equipment
is used independently
without turning the power of this
unit on. If this happens, turn on the power of the this unit.
[_]
_
_]Ta
[_._,,1_Ii_1
• When making connections,
also refer to the operating instructions
of the other components.
The power to these outlets is turned on and off when the power is switched
between
on and standby from the remote control unit or power
switch.
OUTPUT
CD player
R
L
[ Connecting
a CD player
]
I -- --
_
OOOO
I C ....... t the CO
player' ..... log output jacks
I El o o
_
_
_'_" I (ANALOG
OUTPUT)
to thisunit's CD jacks using
[
_
v
j
pin plug cords.
[ Connecting
a turntable
1
Connect
the turntable's
output cord to the AVR-1804/884's
PHONO
jacks, the L (left) plug to the L jack, the R (right) plug to the right jack.
NOTES:
• This unit cannot
be used with
MC cartridges
directly.
Use a
separate
head amplifier
or step=up transformer.
• If humming
or other noise is generated
when the ground
wire
is connected,
disconnect
the ground
wire.
Turntable
(MM cartridge)
/
Ground
wire
I
I
OPTICAL
MD recorder, CD recorder
or other component
equipped
with digital input/output
jack
_oo
[
]o_F_
--
--
_
aa_
]
CD player or other
[3 o o
_
O =
O
component
equipped
with digital output jacks
OUTPUT
[ Connecting
the
DIGITAL
jacks
]
Use these for connections
to audio (video) equipment
with digital output.
Refer to page 26
for instructions
on setting
this terminal.
NOTES:
• Use 75 £,_/ohms cable pin cords for coaxial connections.
• Use optical cables for optical connections,
removing
the cap before
connecting.
• The main unit's power
must be turned on when recording
via the AVR-1804/884.
R
L
R
L
INPUT
OUTPUT
t Connecting
the
AC OUTLETS
t
AC OUTLETS
• SWITCHED
(total capacity - 120 W (1 A.))
The power
to these
outlets
is turned
on and off
in conjunction
with the
POWER operation switch
on the main unit, and when the power
is switched
between
on and standby
from the remote
control
unit.
No power
is supplied
from these outlets when this unit's power is at standby.
Never connect
equipment
whose
total capacity is above
120 W (1 A.).
NOTE:
Only use tile AC OUTLETS
for audio equiprneet.
Never
use them for hair
driers, TVs or other electrical
appliances.
I Subwoofer
jack
]
Connect
the internal amplifier's
subwoofer
to the
subwoofer
terminal.
(Refer to page 17.)
Route the connection
cords, etc., in such a way
that they do not obstruct the ventilation
holes.
AC 120 V, 60 Hz
CD recorder
or Tape deck
NOTE:
[:
.....]
----
If humming
noise
is generated
by a
o o
[_}
o _ _ _ @
tape
deck,
etc., move
the tape
deck
, _
_,
away.
I Connecting
a tape
deck
I
Connections
for recording:
Connect
the tape deck's recording
input jacks (LINE IN or REC) to this unit's tape
recording (CDR/TAPE OUT) jacks using pin plug cords.
Connections
for playback:
Connect
the tape deck's playback
output jacks (LINE OUT or PB) to this unit's tape
playback (CDR/TAPE IN) jacks using pin plug cords.
10
Publicité
