Télécharger Imprimer la page

Hurricane HTG 98 SD Manuel D'utilisation page 62

Publicité

Les langues disponibles
  • FR

Les langues disponibles

31. Warning: Read the instructions before op-
erating the machine.
32. Warning:  Disconnect the key and read the 
instructions before carrying out any mainte-
nance or repair work.
33. Danger! Ejected objects: do not operate
without side discharge chute in place.
34. Danger! Ejected objects: Keep bystand-
ers away.
35. Danger! Machine rollover: Do not use this
machine on slopes greater than 10°.
36. Danger! Dismemberment: Make sure that 
children stay clear of the machine all the 
time when engine is running.
37. Danger of cutting yourself. Cutting
means in motion. Do not put hands or feet 
near or under the opening of the cutting
means housing.
38. Warning! Keep away from hot surfaces.
2.4 REGULATIONS FOR TOWING
A kit for towing a small trailer is available on re-
quest. This attachment must be fitted following 
the instructions provided.
41.    W hen using the towing kit, do not exceed 
the recommended loads stated on the label 
and follow the safety instructions. 
NOTE The images corresponding to the texts
in chapters 3 et seq., can be found on pages iii et
seq. of this manual.
3. UNPACKING AND ASSEMBLY
For storage and transport purposes, some com-
ponents of the machine are not installed in the 
factory and have to be assembled after unpack-
ing. Follow the instructions below.
IMPORTANT The machine is supplied without
engine oil or fuel. Before starting up the engine,
fill with oil and fuel following the instructions given
in the engine manual.
WARNING!
Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for mov-
ing the machine and its packaging, always
making use of suitable equipment.
3.1 UNPACKING
When unpacking the machine, take care to 
gather all individual parts and fittings, and do 
not damage the cutting-means assembly when 
taking the machine off the pallet.
The standard packaging contains:
–    t he machine;
–    t he steering wheel;
–  dashboard cover;
–    t he seat;
–    t he battery;
– the side discharge chute
–    a n envelope containing:
    –    t he instruction manuals and documents,
    –    s teering wheel assembly parts,
    –    n uts and bolts to assemble the seat  and 
the supplied side discharge chute
    –    t he connection screws for the battery 
cables
    –    2  starter keys, 
    –    1  spare 10 A fuse.
NOTE
To avoid damaging the cutting-means
assembly when getting the machine down from
the pallet, take it to the maximum height and be
very careful.
Hydrostatic transmission
–    T o make it easier to get the machine off 
the pallet and to move it, the rear drive 
disengage lever should be put in position
«B» (see 4.33).
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
3.2 FITTING THE STEERING WHEEL
• Steering wheel Type "I" (Fig. 3.1)
Put the machine on a flat surface and straighten 
the front wheels.
Mount the hub (1) on the shaft (2), making sure 
that the plug (3) is correctly fitted into the hub 
seat.
Fit the dashboard cover (4) clicking the seven 
fasteners into place.
Fit the steering wheel (5) onto the hub (1) with 
the spokes directed towards the seat.
Fit the spacer (6) and fasten the steering wheel 
in place using the screws supplied (7), in the 
indicated order.
Fit the steering wheel cover (8) clicking the three 
fasteners into place.
• Steering wheel Type "Il" (Fig. 3.2)
Put the machine on a flat surface and straighten 
the front wheels.
Mount the hub (1) on the shaft (2), making sure 
that the plug (3) is correctly fitted into the hub 
seat.
6

Publicité

loading