Tunturi C80-R Manuel De L'utilisateur page 22

English
To stop your workout see:
"End your workout"
Watt constant
- Turn the jog wheel and select
"Watt Constant"
- Press the jog wheel to confirm and enter the Setting
screen (Fig.F-10).
- Turn the jog wheel to adjust target Watt value.
- Press the jog wheel to confirm and enter the Setting
screen (2) (Fig. F-11)
- Turn jog wheel to select item
- Press the jog wheel button for confirmation and
continue the range setting at the right.
- Turn jog wheel to change setting ranges
- Press the jog wheel button to confirm and enter the
Workout screen (Fig. F-12)
The X-axis unit is shown according to the selection of
Energy/Time/Distance in Set screen.
Energy Unit:
Time Unit:
Distance Unit: km in metric
- During workout, press the jog wheel button to
switch the Y-axis between Nm - bpm
- The bar chart denotes the Watt value. Rotate the
jog wheel to adjust the Watt value
- The white dot line shows current position, which
moves rightward as calorie /time/distance increases
- The orange curve shows the user's actual heart rate,
which varies as the heart rate frequency goes up
and down
- Console programming: Assist the user to achieve
the target according to its target Watt value input
during workout. When actual Watt value > target
value, the system would decrease Watt value; while
increases Watt value when actual Watt rate < target
value.
To stop your workout see:
"End your workout"
T-Ride
- Turn the jog wheel and select
"T-ride"
- Press the jog wheel to confirm and enter the Setting
screen (Fig F-13).
- Turn the jog wheel to select between: Top and
Down - Trail - Easy Ride - Marathon - Short Loop
- Press the jog wheel to confirm and enter the Setting
screen (2) (Fig. F-14)
- Set up the Startup point of Workout: rotate the jog
wheel button to adjust the left white dot line, press
the jog wheel button for confirmation.
kcal
min
mile in Imperial
- Set up the Ending point of Workout: rotate the
jog wheel button to adjust the right white dot line,
press the jog wheel button for confirmation then
enter the Workout screen. (Fig. F-15)
The X-axis is shown as distance unit, km in metric and
mile in Imperial
- During workout, press the jog wheel button to
switch the Y-axis between m-bpm in metric, ft-bpm
in imperial
- The white dot line shows current position, which
moves rightward as distance increases
- In the right of the screen is the gear shift from 1~8,
Turn the jog wheel button to switch
- The white icon + 0°in the left bottom of the screen
shows the incline level and it varies with the Profile
incline level change.
- The Last Session screen shows workout data. Press
the jog wheel button to return to Main menu
To stop your workout see:
"End your workout"
Preset Programme
- Turn the jog wheel and select
"Preset Programs"
- Press the jog wheel to confirm and enter the Setting
screen (Fig. F-16).
- Turn the jog wheel to select between:
- Watt control: Rolling Hills - Hill Climb - Cross
Country - Stamina - Power Interval items and,
Heart Rate Control: Fat burner 1 - Fat burner 2 -
Cardio Strength -
Cardio Climb - Cardio Interval
- Press the jog wheel to confirm and enter the Setting
screen (2) (Fig. F-17)
- Turn jog wheel to select item
- Press the jog wheel button for confirmation and
continue the range setting at the right.
- Turn jog wheel to change setting ranges
- Press the jog wheel button to confirm and enter the
Workout screen. (Fig F-18)
- Turn jog wheel to select item
- Press the jog wheel button for confirmation and
continue the range setting at the right.
- Turn jog wheel to change setting ranges
- Press the jog wheel button to confirm and enter the
Workout screen.
-
NOTE
Workout screen:
Workout screen is depending on the trainings mode
you are in.
Nm manual mode
It's the same as Manual mode
2 2