Würth EWS 28-A Traduction Des Instructions De Service D'origine page 15

EWS 28-A.book Seite 15 Donnerstag, 1. Februar 2018 3:04 15
Tool Specifications
Cordless Angle Grinder
Artikelnummer
Rated voltage
No-load speed
Grinding disc dia.
Grinder spindle thread
Weight (with battery)
Battery LI-Ion LI-2-28 V LI-2-28V
Part number 0700 957
730
Rated voltage 28 V
Capacity 3.0 Ah
Number of cells 1 x 7
Weight, approx. 1.0 kg
Machine Elements
1 Spindle lock button
2 Grinder spindle
3 Protection guard
4 Mounting flange
5 Grinding/cutting disc*
6 Clamping nut*
7 Two-pin spanner for clamping nut*
8 Quick-clamping nut
9 On/Off switch
10 Battery
11 Auxiliary handle
12 Battery unlocking buttons
13 Battery charge-control indicator
14 Button
* Optional accessories
Not all of the accessories illustrated or described are included
as standard delivery.
Intended Use
The machine is intended for cutting, roughing, grinding
and brushing of metal materials, as well as for working
stone. The machine is not intended for working with dia-
mond cutting heads.
For damage caused by usage other then intended, the
user is responsible.
Before Putting into Operation
The batteries are partially charged and delivered in idle
EWS 28-A
state. The battery must be activated before using for the
0700 237 X
first time. For this, place the battery onto the charger for
28 V a short time. The LED 13 on the battery indicates the
charge condition (see main figure).
9 000 rpm
When the battery is not used for longer periods, it
115/125 mm
switches to the idle state. In order to use the battery
M 14
again, it must be reactivated.
2,8 kg
When the battery is completely discharged, it switches
off automatically (deep discharging not possible).
When the power tool is switched on nonetheless, the
battery delivers only brief current pulses. The power tool
0700 957 0700 957
"flickers" as an indication that the battery must be
730 731
charged.
28 V 28 V
As a general rule: Should the power tool not be opera-
3.0 Ah 5.0 Ah
tive after inserting the battery, place the battery onto the
2 x 7 2 x 7
charger. The indicators on the battery and the charger
1.0 kg 1.0 kg
then provide information about the battery condition
(see main figure).
At low temperatures, further operation is possible with
reduced power output. The battery switches off auto-
matically below –10 °C.
When storing the battery longer than 30 days:
Store the battery dry and at approx. 27 °C.
Store the battery charged at approx. 30 % – 50 %.
Recharge the battery every 6 months.
Battery Charging
A battery that is new or has not been used for a longer
period does not develop its full capacity until after
approximately 2 – 3 charging/discharging cycles.
To remove the battery 10, press the unlocking but-
tons 12 and pull out the battery toward the rear. Do not
exert any force.
Please refer to the enclosed "Battery Charger" instruc-
tions for the operation of the battery charger as well as
for a description of the charging process.
The battery is equipped with an NTC temperature con-
trol which allows charging only within a temperature
range of between –10 °C and +66 °C. A long battery
service life is achieved in this manner.
A significantly reduced working period after charging
indicates that the batteries are used and must be
replaced.
Observe the notes on environmental protection.
Charge-control Indicator (see Main Figure)
The battery 10 is fitted with a charge-control indica-
tor 13.
By pressing the button 14, the battery charge can also
be checked when the battery has been removed, or
when the machine is at a standstill (machine must be
switched off for at least 1 minute). After approx. 4 sec-
onds the battery charge display automatically turns off.
15