Barbecook SIESTA 310 Mode D'emploi page 7

MAN_GAS_SIESTA_310_310_CREME_BBC_151001_B.book Page 7 Thursday, October 1, 2015 9:14 AM
4.2 Burner hoods
The burner hoods are the hoods that you mount above the
burners of your appliance. They protect the burners from
dripping fat. The holes at the sides of the hoods also distribute
the heat over the grill, so it is heated much faster and more
evenly.
4.3 Enamel
Some parts of the appliance are covered in a layer of melted
glass, called enamel. This enamel protects the underlying metal
from corrosion. Enamel is a high-quality material: it is resistant to
rust, does not fade under the influence of high temperatures and
is very easy to maintain.
1
Because the enamel is less flexible than the metal which
it covers, pieces of enamel can chip off when you handle
the appliance incorrectly. To avoid problems, be careful
when assembling enamelled parts and always maintain
the enamel as described further in this manual.
4.4 Flare-ups
Flare-ups are sudden flames that spark from the bowl when you
are grilling. They are usually caused by dripping fat or marinade.
5 ASSEMBLING THE APPLIANCE
5.1 Safety instructions
• Do not modify the appliance when assembling it. It is very
dangerous and not allowed to alter parts that are
pre-assembled and/or sealed by the manufacturer.
• Always follow the assembly instructions carefully.
• The user is responsible for the correct assembly of the
appliance. Damages caused by improper assembly are not
covered by the warranty.
5.2 To assemble the appliance
You need a cross-slotted screwdriver, a flat-slotted screwdriver
and an AA battery (electrical igniter). There are no batteries
supplied with the appliance.
1 Put the appliance on a flat and clean surface.
2 Assemble the appliance as shown on the assembly
drawings. You find them in the second part of this manual,
after the exploded view of your appliance.
0
To make the assembly easier, some screws are
premounted in the correct screw hole. You have to loosen
these screws a few millimeters before assembling the
appliance. This allows you to slide parts over the screws
and tighten them very easily.
1
Be careful when assembling enamelled parts. The tools
and screws may damage the enamel. Use the provided
fiber washers to protect the enamel around the screws.
0
The blister packs can contain more screws than
necessary. Screws can be left over after the assembly.
6 CONNECTING GAS TO THE
APPLIANCE
6.1 Which cylinder, hose and regulator?
Before you can connect gas to the appliance, you have to buy a
gas cylinder, hose and pressure regulator. Always buy materials
that comply with all national standards and with the gas type(s)
and nominal pressure(s) mentioned on the appliance.
The table below shows you which cylinder, hose and regulator
you have to use. In Belgium (BE), for example, you have to use a
propane cylinder with a hose and regulator for 37 mbar or a
butane cylinder with a hose and regulator for 28-30 mbar.
Country
DK, GR, NO, SE,
EE, LT, LV, CZ, PL,
MT, HU, SI, SK, NL
ES, GB, IE, PT, BE,
FR, LU, IT, CY
2
We recommend connecting the appliance to propane.
Propane offers a high-quality combustion and is less
sensitive to frost.
2
Buy your pressure regulator and gas cylinder together.
Not all regulators fit all cylinders.
6.2 Safety instructions
• Never connect the cylinder directly to the appliance. Always
mount a pressure regulator on the cylinder first.
• Never modify pre-assembled or sealed parts of the cylinder,
the hose or the pressure regulator.
• Keep the hose as short as possible (1,5 m maximum) to
prevent it from dragging on the ground.
• While connecting the cylinder, hose and pressure regulator:
- Never distort the hose.
- Always keep the cylinder in an upright position.
- Never open the gas supply.
• Check for leaks each time you make changes to the gas
connection. See "7 Checking for gas leaks".
6.3 Connecting the hose to the
appliance
To connect the gas hose to the appliance, you have to mount a
coupling on the gas tube of the appliance. The appliance comes
with two couplings, both intended for particular countries:
Country
BE, CH, CZ, DK, ES, FI, GB, IE, IT, PT, SI
FR
2
If your country is not in the table, use the coupling that
complies with your national standards.
www.barbecook.com
Cylinder, hose and regulator
Propane, 30 mbar / Butane, 30 mbar
Propane, 37 mbar / Butane, 28-30 mbar
Coupling
Coupling A
Coupling B
7