Swegon TAC5F Manuel D'installation page 10

If # FAN=F1 : only 1 fan
10 m³h K1?
11 m³h K2?
12 m³h K3?
13 CONFIG
TIME? N
14 TIME
SEGMENT ?N
15 DAY OFF
N
16 PRESSURE
ALARM?N
If PRESSURE ALARM is set to Yes
∆P FAN 1
17
18 INIT Pa REF?
If INIT Pa REF is set to Yes
19 m³h INIT
20 Pa REF
INIT
xxxx m³h
xxxx Pa
21 RESET
ALARMS?
22 END SETUP
If #FAN=F1 + F2 : 2 fans
If F2=%F1 is set to yes: 2 dependent fans
10 m³h K1?
11 m³h K2?
12 m³h K3?
13 %F1/F2
If F2=%F1 is set to no: 2 independent fans
10 m³h-1 F1?
11 m³h-2 F1?
12 m³h-3 F1?
13 m³h-1 F2?
14 m³h-2 F2?
15 m³h-3 F2?
16 CONFIG
TIME? N
17 TIME
SEGMENT ?N
18
DAY OFF
N
19 PRESSURE
ALARM?N
If PRESSURE ALARM is set to Yes
∆P FAN 1
20
∆P FAN 2
21
22 INIT Pa REF?
Select Airflow 1 (contacts between terminals K1 and +12V closed)
Select Airflow 2 (contacts between terminals K2 and +12V closed)
Select Airflow 3 (contacts between terminals K3 and +12V closed)
Select Y to configure time and date. See § 3.2.1
Select Y to activate the time segment scheduling function. See § 3.2.1
Select Y if you wish to activate the day OFF option. See § 3.2.1
Pressure alarm is optional. If you do not wish to set a pressure alarm select N(o),
otherwise select Y(es). (not available for fans 720999 and 720998)
Configuration of pressure alarm on fan 1:
Select value of pressure increment corresponding to the nominal airflow
Configuration of pressure alarm: Do you wish to (re)define the nominal pressure
corresponding to a new nominal airflow?
If Y is selected, enter nominal airflow at which you wish to initialize the reference
pressure.
Initializing the reference pressure...
After +/-1 minute, the system will memorize the calculated pressure value of the fan
as the reference pressure. While initializing the airflow and pressure on F1 is
displayed.
Possibility to reset the alarms. Y or N?
The setup is then completed.
Select Airflow 1 for fan 1 (contacts between terminals K1 and +12V closed)
Select Airflow 2 for fan 1 (contacts between terminals K2 and +12V closed)
Select Airflow 3 for fan 1 (contacts between terminals K3 and +12V closed)
Choose the rate between fan 2 and 1 airflow
Select Airflow 1 for fan 1 (contacts between terminals K1 and +12V closed)
Select Airflow 2 for fan 1 (contacts between terminals K2 and +12V closed)
Select Airflow 3 for fan 1 (contacts between terminals K3 and +12V closed)
Select Airflow 1 for fan 2 (contacts between terminals K1 and +12V closed)
Select Airflow 2 for fan 2 (contacts between terminals K2 and +12V closed)
Select Airflow 3 for fan 2 (contacts between terminals K3 and +12V closed)
Select Y to configure time and date. See § 3.2.1
Select Y to activate the time segment scheduling function. See § 3.2.1
Select Y if you wish to activate the day OFF option. See § 3.2.1
Pressure alarm is optional. If you do not wish to set a pressure alarm select N(o),
otherwise select Y(es). (not available for fans 720999 and 720998)
Configuration of pressure alarm on fan 1:
Select value of pressure increment corresponding to the nominal airflow
Configuration of pressure alarm on fan 2:
Select value of pressure increment corresponding to the nominal airflow
Configuration of pressure alarm: Do you wish to (re)define the nominal pressure
corresponding to a new nominal airflow?
12