Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
- When the thread spool is empty replace it by a genuine
thread spool.
Thread follow-up
During trimming, the cutting thread wears (becomes shorter) or
it may tear off so that it can no longer cut grass.
Shortly press the machine against solid ground. This will
extend the cutting thread (by approx. 2,5 cm). If the cutting
thread exceeds the maximum cutting diameter it will be
shortened by the integrated knife within the protective hood.
Maintenance and care
Before each maintenance and cleaning work
− Stop the engine.
− Wait until the cutting device does not longer
move.
− Remove the spark plug connector.
− Wear protective gloves in order to avoid injury
to the hands.
− Do not carry out maintenance work close to
open flames. Risk of fire!
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
Use only original parts. Other parts can result in unexpected
damages and injuries.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
M
a
i
n
t
M
a
i
n
t
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the device carry out
the following maintenance works regularly.
Check the machine for obvious defects such as
− loose, hung out or damaged cutting tools
− worn or damaged components
− correct assembly and faultless covers and protective devic-
es
Necessary repair works or maintenance works have to be
carried out before the usage of the machine.
R
e
p
l
a
c
i
n
g
t
h
R
e
p
l
a
c
i
n
g
t
h
Press on both locking tabs on the bottom part of the
thread spool and pull off the upper
Remove the thread release stylus (M), compression
spring (N) and the thread spool (O).
Remove dirt and grass
residues.
Insert a new thread spool. Thread each thread individ-
24
All manuals and user guides at all-guides.com
e
n
a
n
c
e
e
n
a
n
c
e
e
t
h
r
e
a
d
s
p
o
o
l
e
t
h
r
e
a
d
s
p
o
o
l
part.
ually in one of the two thread guides in the bottom part of the
spool.
Place the compression spring (N) and the thread release
stylus (M).
The cut-outs on the thread spool cover need to be
aligned with the locking tabs. Press the thread spool cover
down until in snaps into place.
R
R
e
e
p
p
l
l
a
a
c
c
i
i
n
n
g
g
t
t
Unscrew the screws and remove the old thread knife (8).
Screw on the new thread knife as shown.
Do not over tighten the screws.
C
u
t
t
i
n
C
u
t
t
i
n
Safe and efficient working is only possible with a
correctly sharpened and intact cutting blade.
Therefore, check the cutting blade for dull edges, bents, cracks
or other damages on a regular basis.
Have dull cutting blades sharpened by a specialist/service
workshop.
Both sides of the cutting blade may be used. Turn round
the cutting blade once and continue to work with the brushcutter
until both sides of the cutting blade are dull-edged.
Replace damaged cutting blades by new ones.
C
l
e
a
n
i
n
g
C
l
e
a
n
i
n
g
Clean the air filter from dust and dirt on a regular basis to
prevent
starting problems,
-
loss of output,
-
too high fuel consumption.
-
Clean the air filter every 8 operating hours, or more frequently in
dusty environments.
Put the choke lever (24) to the position OFF to prevent
dirt from entering the carburetor
Remove the air filter housing (18) using the screwdriver (15).
Remove the air filter cover
Remove the air filter (39).
Wash the air filter in a luke warm soapy solution.
Do not puff/blow out dirt particles; otherwise there is a
risk of eye injury.
Allow the air filter to dry well and reinsert it.
Damaged air filters must be replaced without delay.
h
h
e
e
t
t
h
h
r
r
e
e
a
a
d
d
k
k
n
n
i
i
f
f
e
e
g
b
l
a
d
e
g
b
l
a
d
e
t
h
e
a
i
r
f
i
l
t
e
r
t
h
e
a
i
r
f
i
l
t
e
r
(38).
Publicité
Table des Matières
