Lenze 8200 vector Instructions De Montage page 181

Code Possible settings
No. Name Lenze
C0034* Range of
v
setpoint
selection
uSEr
Standard I/O
(X3/8)
C0034* Range of
v
setpoint
selection
(A)
Application I/O
uSEr
1 X3/1U, X3/1I
2 X3/2U, X3/2I
C0037 JOG1 20.00 −650.00
C0038 JOG2 30.00 −650.00
C0039 JOG3 40.00 −650.00
C0050* Output
frequency
uSEr
(MCTRL1−NOUT)
à
C0087 Rated motor
speed
à
C0088 Rated motor
current
C0089 Rated motor
frequency
à
C0090 Rated motor
voltage
à
Motor cos 
C0091
C0119 Configuration of
v
motor
temperature
monitoring (PTC
input) / earth
fault detection
EDK82EV903 DE/EN/FR 5.1
Important codes for quick commissioning
Selection
0 0 Unipolar voltage 0 ... 5 V / 0 ... 10 V
Current 0 ... 20 mA
1 Current 4 ... 20 mA
2 Bipolar voltage −10 V ... +10 V
3 Current 4 ... 20 mA open−circuit monitored
0
0 Unipolar voltage 0 ... 5 V / 0 ... 10 V
1 Bipolar voltage −10 V ... +10 V
2 Current 0 ... 20 mA
3 Current 4 ... 20 mA
4 Current 4 ... 20 mA open−circuit monitored
{0.02 Hz}
{0.02 Hz}
{0.02 Hz}
−650.00 {Hz}
300 {1 rpm}
0.0 0.1 (A)
50 10 {1 Hz}
50 {1 V}
0.40 {0.1}
0
0 PTC input inactive
1 PTC input active,
TRIP effected
2 PTC input active,
warning effected
3 PTC input inactive
4 PTC input active,
TRIP effected
5 PTC input active,
warning effected
l
Commissioning
IMPORTANT
Observe switch position of the
function module!
Reversal of rotation direction only
possible with a digital signal.
l
Minimum output frequency
(C0010) not effective
l Individually adjust offset and gain
TRIP Sd5 if I < 4 mA
Reversal of rotation direction only
possible with a digital signal.
Observe jumper position of the
function module!
Minimum output frequency (C0010)
not effective
Reversal of rotation direction only
possible with a digital signal.
Reversal of rotation direction only
possible with a digital signal.
TRIP Sd5 at I < 4 mA
650.00 JOG = fixed setpoint
Additional fixed setpoints ðC0440
650.00
650.00
650.00 Read only: Output frequency without
slip compensation
à
16000 Device−dependent
à
650.0 Device−dependent
0.0 ... 2.0 x rated output current of the
controller
960
à
500 230 V for 230 V controllers,
400 V for 400 V controllers
à
1.0 Device−dependent
l
Earth fault detection Configure signal output in C0415
active
l
If several parameter sets are used,
monitoring has to be set
separately for every parameter set.
l
Deactivate earth fault detection if
the earth fault detection is
Earth fault detection
actuated unintentionally.
inactive
l If the earth fault detection is
activated, the motor starts with a
delay of approx. 40 ms after
controller enable has been set.
7
181