Product Disposal - Nice AVIO600 Instructions Et Avertissements Pour L'installation Et L'utilisation

4 To check the photocells (if provided), pass a 5 cm diameter, 30 cm long
cylinder on the optical axis, first near TX, then near RX and finally at the
mid-point between them and make sure that in all these cases the device
is triggered, switching from the active to the alarm status and vice-versa;
finally, that it causes the intended action in the control unit, for example:
that it causes the reversal of the movement during the closing manoeuvre.
78
5 The control of the correct obstacle detection is performed with the
700x300x200mm test parallelepiped with 3 black sides and 3 polished
white or mirrored sides, according to the EN 12445 standard.
6 Measure the impact force according to EN standards 12445 and 12453.
If "motor force" control is used to assist the system for the reduction of the
impact force, try to find the adjustment that gives the best results.
7 Ensure that the entire mechanism is correctly adjusted and that the
automation system inverts the manoeuvre when the door collides with a
50 mm high object on the floor.
8 Ensure that the automation prevents or blocks the opening manoeuvre
when the door is loaded with a mass of 20 kg, fixed in the middle of the
door's lower edge.
3.7.2 – Commissioning
The commissioning operations can be performed only after all the
tests have been successfully carried out. Partial commissioning
or implementation of "temporary" conditions are not permitted.
1 Prepare the technical documentation for the automation, which must
include at least: assembly drawing (e.g. figure 1), wiring diagram (e.g. fig-
ure 65), analysis of hazards and solutions adopted, manufacturer's decla-
ration of conformity of all the devices installed. For AVIO use Annex 1 "CE
Declaration of Conformity".
2 Post a label on the door providing at least the following data: type of
automation, name and address of manufacturer (person responsible for the
"commissioning"), serial number, year of manufacture and "CE" marking.
––– STEP 4 –––
The maintenance operations must be performed in strict com-
pliance with the safety directions provided in this manual and
according to the applicable legislation and standards.
The devices used for the AVIO automation system do not require any spe-
cial maintenance. However, periodically make sure (at least once every six
This product is an integral part of the automation system it con-
trols and must be disposed of along with it.
As in installation operations, at the end of the product's lifespan, disposal
operations must be performed by qualified personnel.
The product is made of various types of materials: some of them may be
recycled, while others must be scrapped. Seek information on the recy-
cling and disposal methods envisaged by the local regulations in your
area for this product category.
Warning! – Some parts of the product may contain polluting or hazard-
ous substances which, if released to the environment, may cause serious
damage to the environment or to human health.
As indicated by the symbol alongside, disposal of this product with house-
hold waste is prohibited. Separate the waste into categories for disposal,
16 – English
3 Fill out the declaration of conformity and deliver it to the owner of the
automation system.
4 Prepare the operating guide and deliver it to the owner of the automa-
tion system; Annex 3 "OPERATING GUIDE" can be used as an example.
5 Prepare the maintenance schedule and deliver it to the owner of the
automation system; it must provide directions regarding the maintenance
of all the automation devices.
6 Attach in a permanent manner the label showing the manual unlocking
and manoeuvre operations (Figure 79) on a clearly visible part of the door.
79
7 Before commissioning the automation system, inform the owner regard-
ing dangers and hazards that are still existing.
8 Post a permanent label or sign with this image on the door (minimum
height 60 mm) with inscription WARNING – RISK OF CRUSHING.
80
MAINTENANCE
months) that all the devices are perfectly efficient.
To this end, carry out all the tests and checks described in paragraph
3.7.1 "Testing" and the operations described in paragraph 6.4 "Mainte-
nance operations to be performed by the user".
If other devices are present, follow the directions provided in the corre-
sponding maintenance schedule.

PRODUCT DISPOSAL

according to the methods established by current legislation in
your area, or return the product to the retailer when purchas-
ing a new version.
Warning! – Local legislation may impose heavy fines in the
event of illegal disposal of this product.
Disposal of buffer battery (if present)
Warning! – Even if discharged, the batteries may contain pollutant sub-
stances and therefore must never be disposed of in normal waste collec-
tion points.
Dispose of according to separate waste collection methods as envisaged
by current local standards.